WEAR AND HEAT CHARACTERIZATION OF BOTH THE AS-CAST AND HEAT EXPOSED SPECIMENS FOR AL/SiC PARTICULATE COMPOSITES
Dewidar, M., A. Khalil, K., Kim, S. (2006). WEAR AND HEAT CHARACTERIZATION OF BOTH THE AS-CAST AND HEAT EXPOSED SPECIMENS FOR AL/SiC PARTICULATE COMPOSITES. EKB Journal Management System, 34(No 6), 1919-1928. doi: 10.21608/jesaun.2006.111339
M. M. Dewidar; Khalil. A. Khalil; Sug-Won Kim. "WEAR AND HEAT CHARACTERIZATION OF BOTH THE AS-CAST AND HEAT EXPOSED SPECIMENS FOR AL/SiC PARTICULATE COMPOSITES". EKB Journal Management System, 34, No 6, 2006, 1919-1928. doi: 10.21608/jesaun.2006.111339
Dewidar, M., A. Khalil, K., Kim, S. (2006). 'WEAR AND HEAT CHARACTERIZATION OF BOTH THE AS-CAST AND HEAT EXPOSED SPECIMENS FOR AL/SiC PARTICULATE COMPOSITES', EKB Journal Management System, 34(No 6), pp. 1919-1928. doi: 10.21608/jesaun.2006.111339
Dewidar, M., A. Khalil, K., Kim, S. WEAR AND HEAT CHARACTERIZATION OF BOTH THE AS-CAST AND HEAT EXPOSED SPECIMENS FOR AL/SiC PARTICULATE COMPOSITES. EKB Journal Management System, 2006; 34(No 6): 1919-1928. doi: 10.21608/jesaun.2006.111339

WEAR AND HEAT CHARACTERIZATION OF BOTH THE AS-CAST AND HEAT EXPOSED SPECIMENS FOR AL/SiC PARTICULATE COMPOSITES

JES. Journal of Engineering Sciences
Article 15, Volume 34, No 6, November and December 2006, Page 1919-1928  XML PDF (650.82 K)
Document Type: Research Paper
DOI: 10.21608/jesaun.2006.111339
View on SCiNiTO View on SCiNiTO
Authors
M. M. Dewidar* 1; Khalil. A. Khalil2; Sug-Won Kim3
1Department of Mechanical Design and Materials, High Institute of Energy, South Valley University, Aswan, Egypt
2-Department of Mechanical Design and Materials, High Institute of Energy, South Valley University, Aswan, Egypt -Division of Advanced Materials Engineering, RIAMD, Chonbuk National University, Jeonju 561-756, South Korea
3Division of Advanced Materials Engineering, RIAMD, Chonbuk National University, Jeonju 561-756, South Korea
Abstract
This Study is to investigate on the wear characterization and heat resistance of aluminum/silicon carbide (Al/SiC) with different particles (3, 5, and 10 μm) composites manufactured by duplex process, which consists of squeeze-infiltration and squeeze casting. Also, this study is to investigate the effect of alloying element (Ni) on the microstructure, wear behavior and heat resistance of Al/SiC composite. Owing to the increase in interfacial area between SiC particles and matrix in both the as-cast and heat exposed specimens (at 250 oC and 350 oC for 5hr), the decrease in nano-SiC particles size resulted in the increase in the hardness of composites. And in case of 3 μm SiC reinforced Al composites as compared with other composites, the highest density of dislocation was generated during manufacture. Composite with 3μm SiC has the lowest wear amount among composites reinforced with 5 and 10μm SiC. Heat resistant property was improved with increasing Ni addition content (wt.) in Al/SiC composites. The wear resistance at 200 oC in argon gas on composite was greater than those at 200 oC and room temperature in the as-composites.
Statistics
Article View: 140
PDF Download: 318