Thermal Simulation in Wire Arc Additive Manufacturing of A 5356 Aluminium Single Track Deposited on 7108 Aluminium Substrate | ||||
| JES. Journal of Engineering Sciences | ||||
| Article 7, Volume 53, Issue 5, September and October 2025, Page 174-186 PDF (777.63 K) | ||||
| Document Type: Research Paper | ||||
| DOI: 10.21608/jesaun.2025.372742.1467 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
Eman Shams   1; Noha Ramadan2; Marwan Abdelwahed3; Nahed ElMahallawy2; Mohamed A Taha2
| ||||
| 11-Mechanical Engineering Department, Faculty of Engineering, Nahda University, New Beni Suef, Egypt 2-Design and Production Engineering Department, Faculty of Engineering, Ain Shams University, Egypt | ||||
| 2Design and Production Engineering Department, Faculty of Engineering, Ain Shams University, Egypt | ||||
| 3Design and Production Engineering Department, Faculty of Engineering. Ain Shams University, Egypt | ||||
| Abstract | ||||
| Wire Arc Additive Manufacturing (WAAM) enables the fabrication of metal components by depositing weld beads through arc-welding techniques. This cost-efficient approach is particularly suited for producing large-scale structures due to its high material deposition rate. Nevertheless, the final quality of the fabricated parts is significantly influenced by complex thermal dynamics occurring throughout the process. Continuous heating and cooling cycles cause heat accumulation, leading to geometric inaccuracies. To analyze these thermal effects, numerical simulation serves as a valuable investigative method. In this study, SIMUFACT-Welding software was used to model and simulate different parameters of WAAM process for producing aluminium single tracks. An adapted version of Goldak’s heat source model is integrated with the material deposition strategy. The simulation captured the thermal profile during deposition and analyzed the effect of energy density on heat flux. This impact influences the molten pool behaviour of the fabricated welded beads. Based on the analysis and simulation outcomes, an optimized heat input was identified and applied in fabricating a single track, that can be used in further analysis to fabricate a 3D metallic product. | ||||
| Keywords | ||||
| WAAM, Welded beads, Goldak heat source; Heat flux, Temperature profile | ||||
| References | ||||
|
[1] L. Zhang, S. Wang, H. Wang, J. Wang, T. Wang, and X. Dai, “Investigate the effect of arc characteristic on the mechanical properties of 5A56 Al alloy in CMT arc additive manufacturing,” CIRP J. Manuf. Sci. Technol., vol. 40, pp. 102–113, 2023, doi: 10.1016/j.cirpj.2022.10.006.
[2] E. Eimer, S. Williams, J. Ding, S. Ganguly, and B. Chehab, “Mechanical performances of the interface between the substrate and deposited material in aluminum wire Direct Energy Deposition,” Mater. Des., vol. 225, p. 111594, 2023, doi: 10.1016/j.matdes.2023.111594.
[3] C. R. Cunningham, J. M. Flynn, A. Shokrani, V. Dhokia, and S. T. Newman, “Invited review article: Strategies and processes for high-quality wire arc additive manufacturing,” Addit. Manuf., vol. 22, pp. 672–686, 2018, doi: 10.1016/j.addma.2018.06.020.
[4] T. S. Senthil, S. R. Babu, M. Puviyarasan, and V. S. Balachandar, “Experimental investigations on the multi-layered SS316L wall fabricated by CMT-based WAAM_ Mechanical and microstructural studies,” J. Alloy. Metall. Syst., vol. 2, no. May, p. 100013, 2023, doi: 10.1016/j.jalmes.2023.100013.
[5] D. Curiel, F. Veiga, A. Suarez, and P. Villanueva, “Advances in Robotic Welding for Metallic Materials: Application of Inspection, Modeling, Monitoring and Automation Techniques,” Metals, vol. 13, no. 4. MDPI, Apr. 01, 2023. doi: 10.3390/met13040711.
[6] C. S. Wu, L. Wang, W. J. Ren, and X. Y. Zhang, “Plasma arc welding: Process, sensing, control and modeling,” J. Manuf. Process., vol. 16, no. 1, pp. 74–85, 2014, doi: 10.1016/j.jmapro.2013.06.004.
[7] M. Aamir, K. Giasin, M. Tolouei-Rad, and A. Vafadar, “A review: drilling performance and hole quality of aluminium alloys for aerospace applications,” J. Mater. Res. Technol., vol. 9, no. 6, pp. 12484–12500, 2020, doi: 10.1016/j.jmrt.2020.09.003.
[8] A. Azarniya, A. K. Taheri, and K. K. Taheri, “Recent advances in ageing of 7xxx series aluminum alloys: A physical metallurgy perspective,” J. Alloys Compd., vol. 781, pp. 945–983, 2019, doi: 10.1016/j.jallcom.2018.11.286.
[9] D. Ding, Z. Pan, D. Cuiuri, and H. Li, “Wire-feed additive manufacturing of metal components: technologies, developments and future interests,” Int J Adv Manuf Technol, vol. 81, no. 1–4. Springer London, pp. 465–481, Oct. 26, 2015. doi: 10.1007/s00170-015-7077-3.
[10] B. Tomar, S. Shiva, and T. Nath, “A review on wire arc additive manufacturing: Processing parameters, defects, quality improvement and recent advances,” Mater. Today Commun., vol. 31, no. January, p. 103739, 2022, doi: 10.1016/j.mtcomm.2022.103739.
[11] V. Kumar, B. K. Roy, and A. Mandal, “Thermal Modeling of Wire Arc Additive Manufacturing Process Using COMSOL Multiphysics,” Advances in Manufacturing Engineering, p. 223, 2022.
[12] P. Stavropoulos and P. Foteinopoulos, “Modelling of additive manufacturing processes: a review and classification,” Manuf. Review, vol. 5, p. 2, 2018.
[13] J. M. Bergheau, “Modélisation numérique des procédés de soudage,” Techniques de l'ingénieur. Génie mécanique BM7758, 2004.
[14] SIMUFACT-welding software:
[15] A. Chergui, F. Villeneuve, N. Beraud, F. Vignat, “Thermal simulation of wire arc additive manufacturing: a new material deposition and heat input modelling,” Int J Interact Des Manuf, vol. 16, pp. 227-237, 2022.
[16] M. P. Mughal, H. Fawad, and R. A. Mufti, “Three dimensional finite-element modelling of deformation in weld-based rapid prototyping,” Proc Inst Mech Eng C J Mech Eng Sci, vol. 220, no. 6, pp. 875- 885, 2006.
[17] F. Jiang, L. Sun, X. Qi, C. Liu, Y. Su, Prof. C. Guo, Dr. J. Wang, “Effects of Heat Input on Morphology of Thin-Wall Components Fabricated by Wire and Arc Additive Manufacturing,” Adv Eng Mater, vol. 23, no. 4, 2020.
[18] S. H. Lee, “CMT-Based Wire Arc Additive Manufacturing Using 316L Stainless Steel: Effect of Heat Accumulation on the Multi-Layer Deposits,” Metals, vol. 10, no. 278. MDPI, Feb. 20, 2020. doi:10.3390/met10020278.
[19] S. Li, L. Zhang, J. Ning, X. Wang, G. Zhang, J. Zhang, S. Na, B. Fatemeh, “Comparative study on the microstructures and properties of wire+arc additively manufactured 5356 aluminium alloy with argon and nitrogen as the shielding gas,” Addit. Manuf. Vol.34, no. 101206, 2020.
| ||||
|
Statistics Article View: 1,346 PDF Download: 306 |
||||
