Effect of low-quality and inexpensive cotton materials on yarn properties using rotor spinning system
Ahmed, H. (2019). Effect of low-quality and inexpensive cotton materials on yarn properties using rotor spinning system. EKB Journal Management System, 9(4), 63-72. doi: 10.21608/idj.2019.82555
Haitham Abdel Daim Mahmoud Ahmed. "Effect of low-quality and inexpensive cotton materials on yarn properties using rotor spinning system". EKB Journal Management System, 9, 4, 2019, 63-72. doi: 10.21608/idj.2019.82555
Ahmed, H. (2019). 'Effect of low-quality and inexpensive cotton materials on yarn properties using rotor spinning system', EKB Journal Management System, 9(4), pp. 63-72. doi: 10.21608/idj.2019.82555
Ahmed, H. Effect of low-quality and inexpensive cotton materials on yarn properties using rotor spinning system. EKB Journal Management System, 2019; 9(4): 63-72. doi: 10.21608/idj.2019.82555

Effect of low-quality and inexpensive cotton materials on yarn properties using rotor spinning system

International Design Journal
Article 5, Volume 9, Issue 4 - Serial Number 32, October 2019, Page 63-72  XML PDF (652.34 K)
Document Type: Original Article
DOI: 10.21608/idj.2019.82555
View on SCiNiTO View on SCiNiTO
Author
Haitham Abdel Daim Mahmoud Ahmed
Lecturer-Spinning, Weaving, and knitting Department, Faculty of Applied Arts, Damietta University, Egypt.
Abstract
The current search aimed to produce medium and coarse yarns using low-quality and inexpensive cotton materials under the rotor spinning at four yarn counts being 10.s, 16.s, 20.s and 24.s with 4.4 twist multiplier. The used cotton materials were the waste from spinning extra long-staple cotton such as combed wastes, Giza 80 lint grade fully good fair, Giza 90 lint grade fully good fair, Giza 80 lint grade good fair, Giza 90 lint grade good fair, imported china variety and carded wastes. The used cotton materials were prepared from the commercial cotton samples of season 2017. The studied yarn mechanical properties were yarn strength, yarn evenness C.V.%, number of neps, number of thin places and number of thick places. However, the average values of five fiber properties being fiber length 2.5 %, short fiber content %, coefficient of variation fiber C.V. %, fiber strength and micronaire reading were measured for all used cotton materials.  Results showed significant differences among cotton materials and among yarn counts for all studied yarn properties. The effect of interaction between cotton materials and yarn counts was only significant for yarn strength and yarn evenness C.V. %.Generally, it is obvious that the mean values of yarn strength were in descending order considering cotton materials of combed wastes, Giza 95 lint grade fully good fair, Giza 90 lint grade fully good fair, Giza 95 lint grade good fair, Giza 90 lint grade good fair, china variety and carded wastes, respectively. On the contrary, the mean values of yarn evenness C.V. %, number of neps, number of thin places and number of thin places were in ascending order for the same aforementioned cotton materials. The mean values of yarn strength were gradually decreased when the yarn count was increased while the mean values of yarn evenness C.V. %, number of neps, number of thin places and number of thin places were gradually increased when the yarn count was increased.
References
  1. Abdel-Ghaffar, Entsar A.F.; G.Y.M. Hammam; A.A.A. El-Hosary; E.M.M. El-Gedwy and A.A. Hassan (2019). Influence of some commercial blends between the imported cotton and the upper Egyptian varieties on technological properties. Annals of Agric. Sci., Moshtohor, Vol. 57 (1): 31 – 38.
  2. Abdel-Khalik, F. S.; E. M. Shoker; S. A. H. Allam; E. M. M. El-Gedwy and A. A. Hassan (2017). Production of low priced, medium and coarse yarns using rotor spinning system. Egypt. J. Appl. Sci., 32 (1): 11-24.
  3. Al Mamun, R.; R. Repon; M.T. Islam and K.Z.M. Abdul Motaleb (2017) Promising effect of processing parameters on yarn properties in rotor spinning. Manufacturing Science and Technology, 4: 11-15.
  4. ASTM (1967). Standards on textile, American society  testing and materials, (D-1578 & D-1907). Philadelphia, USA.
  5. ASTM (1984). Standards on textile, American society  testing and materials, (D-1445 & D-2256). Philadelphia, USA.
  6. Halimi M. T.; M. Ben Hassen; B. Azzouz and F. Sakli (2006). Effect of cotton waste and spinning parameters on rotor yarn quality. The Journal of The Textile Institute, 98 (5): 437–442.
  7. Hassan, S. K.; S. M. Hassan; S. Naseem and M. Iqbal (2016). Evaluation of factors affecting the fiber quality used for yarn production. Current Science Perspectives, 2(4): 116-119.
  8. Hollen, N, and J. Saddlers (1973). Textile Macmillan co., New-York.
  9. Khan, K.R. and H. Rahman (2015). Study of effect of rotor speed, combing-roll speed and type of recycled waste on rotor yarn quality using response surface methodology. IOSR Journal of Polymer and Textile Engineering, 2 (1): 47-55.
  10. Kotb, N.A. (2012). Predicting yarn quality performance based on fibers types and yarn structure. Life Science Journal, 9(3): 1009-1015.
  11. Mabrouk, K. I. K. and M. D. O. Nour (2005). Possibility of spinning and blending the waste of carding and combing for coarse count on the Open-End rotor spinning. Egypt Agric. Res., 83 (3): 1305-1315.
  12. Mohammed, A. M. and M. A. M. El-Sayed (2002). Processing of wastes and low quality cottons on the open -end rotor spinning. Agric. Res. J., 80 (4): 1709-1718.
  13. MWASIAGI J.I. and J. Mirembe (2018). Influence of spining parameters on thin and thick places of rotor spun yarns. International Journal Of Computational And Experimental Science And Engineering, 4 (2): 1-7.
  14. Repon, R.; R. Al Mamun; S. Reza, M. Kumer Das and T. (2016). Effect of spinning parameters on thick, thin places and neps of rotor spun yarn. Journal of Textile Science and Technology, 2: 47-55.
  15. Snedecor, G. W. and W. G. Cochron (1989). Statistical Methods. 8th Ed., Iowa State Univ. Press, Ames Iowa, USA.
  16. Taher, M. H.; A. Bechir; H. Mohamed and S. Faouzi (2009). Influence of spinning parameters and recovered fibers from cotton waste on the uniformity and hairiness of rotor spun yarn. J. Eng., Fibers & Fabrics, 4 (3): 36-44.
  17. Tolba, F. S. A. (2017). Production of low priced, medium and coarse yarns using rotor spinning system. M. Sc. Thesis, Fac. of Agric., Benha Univ., Egypt.
  18. Ul-Hasan, N.; F. Afroz; M. M. Islam; Z. Islam and R. Hasan (2014). Comparative study of mechanical properties, TPI, hairiness and evenness of conventional ring and modern rotor spun yarn. European Scientific Journal, 10: 1857 – 7881.
Wanassi B.; M. Ben Hassen and B. Azouz (2018). Industrial cotton waste: recycling, reclaimed fiber 

Statistics
Article View: 476
PDF Download: 546