PERFORMANCE EVALUATION OF FARM TRACTOR USING VARIABLE WEIGHTS ON REAR WHEELS DURING PLOUGHING AND SOWING OPERATIONS | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 5, Volume 30, Issue 3, July 2013, Page 645-660 PDF (473.9 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2013.101930 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| H. A. Jebur1; M. M. Mostafa2; E. A. El-Sahhar2; M. A. Elnono2; M. A. El-Attar3 | ||||
| 1Graduate student, Ag. Eng. Dept., Fac. of Ag., Ain Shams Univ., Egypt. | ||||
| 2Ag. Eng. Dept., Fac. of Ag., Ain Shams Univ., Egypt. | ||||
| 3Sen. Res., Ag. Eng. Res. Inst., Ag. Res. Center, Dokki, Giza, Egypt. | ||||
| Abstract | ||||
| The general objectives of this study were to investigate the performance characteristics of a farm tractor during ploughing (chisel plough) and sowing (seed drill) using variable weights from (0 to 500 kg) on the rear tractor wheels, and different traveling speeds from (2.78 to 5.68 km/h). the ploughing depths were (15-20 cm) , and the average moisture content was (20.15 %). The soil texture was found to be a (Silty clay). The rear tier sizes of the tractor and inflation pressure were 16.9/14-38 and 150 kPa, respectively. The study was concentrated on the rate of fuel consumption, required power, specific energy, drawbar pull, tractor wheel slippage, tractive efficiency, effective field capacity and field efficiency. The obtained results, for the range of tests, showed that the use of 500 kg weight on the tractor rear wheel at 3.1 km/h traveling speed produced the highest value (74.4 %) of tractive efficiency, in case of chisel plough operation, and (in the mean time) the wheel slippage, filed efficiency, fuel consumption, required power, specific energy were 7.46 %, 80.22%, 15.11 l/h, 46.58 kW, and 43.13 kW.h/fed, respectively. While in case of seed drill operation, the use of 500 kg weight at 3.07 km/h traveling speed produced the highest value (57.7 %) of tractive efficiency, and the wheel slippage, filed efficiency, fuel consumption, required power, specific energy were 2.84 %, 76.55 %, 4.63 l/h, 14.27 kW, and 8.25 kW.h/fed, respectively. In general, the traveling speed and the weight on the rear tractor wheels were the most important factors that affecting the drawbar pull and the specific energy. | ||||
| Keywords | ||||
| Tractor; Energy; Chisel plough; Seed drill; Weight; Power | ||||
| References | ||||
|
Abbaspour-Gilandeh. Y, M. Omid and A. Keyhani, (2007). Simulation Program for Predicting Tractor Field Performance. World applied Sciences Journal 2(5): 552-558.
Abu-Hamdeh, N.II. and M.L.Al-Widyan, (1998). Effect axle load, tire inflation pressure and tillage system on soil physical properties and crop yield of a Jordanian soil. ASAE paper no.98-1060, ASAE, St. Joseph, MI 49085, USA.
Al-Ashry, A.S, (1994). Proper size of tractor in local greenhouse. Ph.D. Thesis, Fac. Agric., Kafr El-Sheikh, Tanta Univ. Egypt.
Barger, E.L.; J.B. Liljedahl; W.M. Carleton and E.G. Mckibben, (1963). Tractor and their power units. 2nd ed., John Wiley&Sons, New york, USA.
Bashford L.L, (1984). Power losses due to slip and motion resistance. Pp No. 84-1564, ASAE, St. Joseph, Mich, 49085, USA.
Black, C.A., D.D. Evans J. L. White , L.E. Ensminger, and F.E. clark, (1965). Method of soil analysis (part1), physical and Mineralogical properties, including statistics of measurements and sampling, American Society of Agronomy, Inc., Publisher Madison, Wisconsin, USA. PP:357-377 and 552-557.
Dahab M.H. and H.A.E. Al-Hashem, (2002). Study on the effect of tractor power and speed on some field performance parameters working on a clay loam soil. J. Agric. Sci. Mansoura Univ., 27(1): 573-582.
El-Ashry E.R., A.I.Mohamed and A. M. Bahnasy, (2003). Effect of wheel ballast, wheel slip and inflation pressure on tractive performance, Misr.J. Agric.Eng., 20(1):PP203-222.
El-Kewey A. A. E, (1992). Effect of diameter and width of drive wheels on tractive efficiency of tractor under local conditions. M.Sc. Thesis, Fac. Of Agric Kafr El-Sheikh., Tanta Univ., Egypt.
El-Khatib. S.I, (1998). Determination and analysis of field performance of a developed cotton transplanter. Ph.D. Thesis, Fac. Agric., Ain Shams, Ain Shams Univ. Egypt.
Embaby, A. T, (1985). A comparison of the different mechanization systems for cereal crop production M. Sc. Thesis, Ag. Eng. Dep., Fac. Of Ag., Cairo Univ.
Jain S.C., and G. Philip, (2003). Farm machinery – an approach. Ist ed. Delhi: standard publishers Distributors.
Lyasko M.I, (2010). How to calculate the effect of soil conditions on tractive performance. Journal of Terramechanics , April , p 1-23.
Mehta C.R, K. Singh, and M.M. Selvan, (2010). A decision support system for selection of tractor-implement system used on Indian farms. Journal of Terramechanics: 1-9.
Mostafa M.M., M.A. El-Gindy, M.N. Saif-Elyazal, and S.I. El-Katib, (1993). Laser land and leveling efficiency and power requirement. Misr.J. Ag.Eng (special-issue): 58-75.
Narang S and A.C Vershney, (2006). Draftability of a 8.95 kW walking tractor on tilled land. Journal of Terramechanics, 43:395-409.
Sahay C.S and V.K. Tewari, (2004). Computer simulation of tractor single-point drawbar performance. Biosystems Engineering 88(4): 419-428.
Sharma D. N., and S.Mukesh, (2010). "Design of agricultural tractor" (principles and problems). Published by Shri Sunil Kumar Jain for Jain Brothers (New Delhi) 16/873, East Park Road, New Delhi – 110 005. First Edition, P.No: 199 – 213.
Younis S.M., R.E EL.Said, F.B. Ahmed., M.E. Islam, (2010). Development a local system for measuring tractors performance. Misr.J. Ag.Eng., January 27(1):34-53. | ||||
|
Statistics Article View: 231 PDF Download: 510 |
||||
