INVESTIGATION OF SOME FACTORS AFFECTING THE HOLE DIGGER PERFORMANCE IN THE SANDY SOIL | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 3, Volume 29, Issue 2, April 2012, Page 553-568 PDF (567.52 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2012.102155 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M. M. Atallah1; S. K. Khalil1; M. T. Ebaid2 | ||||
| 1Res., Ag. Eng. Res. Institute, Egypt. | ||||
| 2Senior Res., Ag. Eng. Res. Institute, Egypt. | ||||
| Abstract | ||||
| The aim of this research is to study some factors affecting the hole diggerperformance in the sandy soil. The experiments were conducted in El-Kasasin Research Station in El-Sharkia Governorate. Auger diameters (250 mm) of the developed hole-digger were tested at different auger–speeds (75, 100 and 150 rpm), auger pitches (10, 15 and 20 cm), hole–depths ( 20, 30 and 40 cm), hole–spacing (5 m) and soil type (sandy) with moisture contents of 15, 22 and 32 % . The obtained results can be summarized as follow: The maximum hole productivity rate for sandy soil was 335 hole/h obtained with auger speed of 150 rpm, hole depth 20 cm, auger pitch 20 cm at moisture content 32 %. The penetration resistance of sandy soil at 15 % moisture content increased by 30 and 40.6 % as compared with of sandy soil at moisture content 22 % and 32 %, respectively. The maximum fuel consumption was 0.59 L/h was obtained with auger speed of 150 rpm, hole depth 40 cm, and auger pitch 10 cm. The maximum power requirements 1.91 kW was obtained with auger speed of 150 rpm, hole depth 40 cm, auger pitch 10 cm and moisture content 15 %. The minimum operation cost was 0.04 L.E/hole at auger pitch 15 cm and hole depth 20 cm. Whereas, the maximum operation cost was 0.14 L.E./hole at auger pitch 10 cm and hole depth 40 cm. The operational cost using a hole digger attached to a power tiller decreased by 371 % compared with manual digging. | ||||
| References | ||||
|
Awady, M. N., 1978, Engineering of tractors and agricultural machinery, Text Bk., col. Ag., Ain-shams U., 5 th. Ed. : 164-167. ( In Arabic. ) ( Updating 1998 ).
Chaaban, M. A., El Awady, M. N., Yehia, I., and Khalil, S. K. 2007, Factors affecting the design of a hole digger attached to a power tiller, environmental, J. Environ. Sci., Vol. 15, No. 1: 83 - 111.
El-Shal, M. S., 1993, A study on some parameters affecting post-hole digger efficiency, Misr J. Agri. Eng., 10 (4): 888 – 899.
Kapnehko, A. H., E-Heb, A. A. and XA-Ahck, B. M., 1976, Farm Machinery (in Russian), Hbl., Book, Moscow: 432-434.
Kathirvel, K., Job, T., Karunanithi, R., Swaminathan, K., 1990, Development of auger digger as attachment to power tiller, AMA, Agr. Mech. In Asia, Africa and Latin America, 21(4): 9-10.
Khalil, S. K., 2008, Development and design of a hole digger to minimize required energy for operation and side effect on agricultural soil, Ph. D., Inst. Environ. Studies and Res., Ain Shams Univ. : 20 - 41.
Miniaei,S. and Alizadeh, 2000, Design and development of auger drill for attachment to two-wheel tractors, Ag. Sc. And tech., 14(1): 19-28.
Purtskhvanidze, M., Keller,N., 1990, Hole digger for slopes, Farm Mechanization (in Russian), No. 3: 38.
Scripnic, V., and Babicin, P., 1968, MASTAGRICOLE, (Book), Romania: 170-191.
Yehia, I., M. H. Kabeel and S. K. Khalil ̣̣̣̣̣̣̣̣̣̣̣̣̣̣̣̣(2009) Affecting factors on performanceof a developed hole digger. Misr J. Ag. Eng. 26(2): 1036-1053. | ||||
|
Statistics Article View: 174 PDF Download: 237 |
||||
