MANUFACTURE AND EVALUATION OF A SIMPLIFIED MACHINE FOR PLANTING OKRA SEEDS | ||||
Misr Journal of Agricultural Engineering | ||||
Article 7, Volume 29, Issue 2, April 2012, Page 633-654 PDF (766.24 K) | ||||
Document Type: Original Article | ||||
DOI: 10.21608/mjae.2012.102278 | ||||
![]() | ||||
Authors | ||||
Moheb M. A. El-Sharabasy; Mahmoud M. A. Ali | ||||
Assist. Prof. of Agric. Eng., Fac. of Agric., Zagazig Univ., Egypt. | ||||
Abstract | ||||
The object of this study was to manufacture and evaluate a simplified planter for planting okra seeds. The okra planter consists of four main parts of three cylindrical ellipsoid hoppers with bored metal strips, furrow openers and covering device. The planter was adjusted to plant okra seeds under the following parameters: three different numbers of holes on the hopper of 3, 4 and 5 holes; four different hole diameters of 6, 6.5, 7 and 7.5 mm; and three different planter forward speeds of 0.55, 0.78 and 1.15 km/h. From obtained laboratory and field tests, it could be concluded the followings: The maximum seed discharged from the hoppers of 8.16, 7.82 and 7.42 kg/fed were achieved at 5 holes number on the hopper and planter forward speeds of 0.55, 0.78 and 1.15 km/h, respectively. The maximum mean seed No. in the hill of 4.91, 4.63 and 4.36 seed/hill were achieved at 4 holes number on the hopper, 7.5 mm hole diameter and planter forward speeds of 0.55, 0.78 and 1.15 km/h, respectively. While these values were decreased to 3.71, 3,38 and 3.08 seed/hill and to 4.43, 4.05 and 3.72 seed/hill at 3 and 5 holes number, 7.5 mm hole diameter and planter forward speed of 0.55, 0.78 and 1.15 km/h, respectively. The minimum values of (C.V.) of 7.96, 9,14 and 14.81 % were occurred at 4 holes number on the hopper, 7 mm hole diameter and planter forward speed of 0.55, 0.78 and 1.15 km/h, respectively.The maximum okra yield of 5.12 Mg/fed was achieved at 4 holes number on the hopper, 7 mm hole diameter and planter forward speed of 0.78 km/h. While, the minimum okra yield of 2.91 Mg/fed was achieved at 5 holes number on the hopper, 6 mm hole diameter and planter forward speed of 0.55 km/h. The minimum energy consumed and planting cost of 0.186 and 41.60 kW.h/fed; 16.10 and 43.90 L.E/fed were obtained at high forward speed of 1.15 km/h for both worker with planter and tractor with planter, respectively. | ||||
References | ||||
Abo El-Naga, M. H. M. (2010): Field performance of a developed machine for direct seeding of soaked and incubated rice grains. Misr J. Agric. Eng., 28 (4) Pp: 1111-1124.
Awady, M. N. (1978): Tractor and farm machinery. Text book, Faculty of Agriculture, Ain-Shams University. Pp: 164-167.
Bamgboye, A. and A. Mofolasayo (2006): Performance evaluation of a two-row Okra planter. Agricultural Engineering International: the CIGR Ejournal. Manuscript PM 06 002. Vol. VIII. July, 2006.
Coates, W. (1992): Performance evaluation of a pendulum spreader. Trans of the ASAE, 8 (3): 285-288.
El-Sharabasy, M. M. A. (2011): Manually operated planter for planting different seeds in small areas. Misr J. Agric. Eng., 28 (4): 865-882.
Gupta, C. P. and Totok Herwanto (1992): Design and development of a direct paddy seeder. Agricultural Mechanization in Asia, Africa and Latin America. Vol. 23, No. 1, Pp. 23-27.
Hunt, D. (1983): Farm power and machinery management. 8th Ed. Iowa state Univ., Press Ames, USA. Ames, Iowa, USA: 364-368.
Kepner, R. A; K. Bainer and E. L. Barger (1982): Principles of farm machinery. 3rd Ed., AVI Pub. Com. Inc., West port. 527 pp.
Kumar, K; N. K. Naaresh and T. P. Ojha (1986): Design, construction and performance of a manually-operated seeding attachment for an animal drawn cultivator. Agricultural Mechanization in Asia, Africa and Latin America. Vol. 17, No. 2, Pp. 35-38.
Lijedahl, J. B; W. M. Carleton, P. K. Turnqist and D. W. Smith (1951): Tractors and their power units. 3rd edition 1979. Chapter one: ‘‘Development of tractor’’.
Molin, J. P. and V. D’Agostini (1996): Development of a rolling punch planter for stony soil conditions. Agricultural Mechanization in Asia, Africa and Latin America. Vol. 27, No 3, Pp 17-19.
Pradhan, S. C; M. Mahapatra, P. K. Samal and B. K. Behera (1997): Development of power tiller–operated groundnut planter cum-“fertilizer drill”. Agricultural Mechanization in Asia, Africa and Latin America. Vol. 28, No. 4, Pp: 25 – 28.
Simalenga, T. E. and N. Hatibu (1991): “Development of low-cost, hand-operated planter”. Agricultural Mechanization in Asia, Africa and Latin America. Vol. 22, No. 3, Pp: 39 – 41.
Sivakumar, S. S; R. Manian, K. Kathirveland G. S. V. Raghavan (2005): Investigation on the influence of machine and operational parameters for the development of a manually-drawn rice seeder for direct sowing. Agricultural Engineering International: the CIGR Ejournal. Vol. VII. Manuscript PM 04 008. May, 2005. | ||||
Statistics Article View: 133 PDF Download: 214 |
||||