EFFECT OF WHEAT GERM PRETREATMENT ON OIL EXTRACTION BY EXPELLING MACHINE | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 19, Volume 29, Issue 2, April 2012, Page 817-836 PDF (628.61 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2012.102353 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M. Mubarak1; M. El-Nono1; T. R. Owies2; A.M. Abdel-Gawad2 | ||||
| 1Agric. Eng. Dep., Fac. of Agric., Ain Shams Univ., Cairo, Egypt. | ||||
| 2Agric., Eng. Res. Inst. (AEnRI), Dokki- Giza, Egypt. | ||||
| Abstract | ||||
| An atmospheric steam process is used for preheating (in the range of 60-70°C) and increasing the moisture content (m.c.) of the wheat germ to study the effect of such process on machine capacity, percentage of oil recovery, percentage of residual oil, and specific energy consumption (SEC)of a double stage expelling machine for wheat germ oil extraction. Four levels of m.c. (13.2, 15.4, 16.2, and 16.8%), and five screw rotation speeds (25, 35, 45, 55, and 65 rpm) were used. It was found that at 25 rpm of screw speed, increasing m.c. from 13.2% (initial m.c.) to 16.2% (wb.), increased the machine capacity by 23.7%, and increased SEC from 0.043 to 0.482kWhkg-1feed(including the energy consumption needed for steam generation). At 16.2% m.c. and 65rpm screw speed, the percentage of oil recovery and oil productivity were 53.42% and 1.97 litter/h, respectively. The maximum percentage of oil recovery (62%) was obtained at 16.2% m.c. and 25rpm screw speed. The economic feasibility data indicated that the total hourly cost was about 11.80EGP/h, and the total cost of oil extraction was about 49.48 EGP/litter of oil. A net annual profit of 160941.3 EGP can be earned providing a Benefit-Cost-Ratio of 1.07, a Return on Investment (ROI) of 106.5% with a Pay-Back Period of 0.07 yr. In addition, the unit would generate an employment of 480 man-days at rural level. | ||||
| Keywords | ||||
| Wheat germ; Preheating - Oil extraction - Expelling machine | ||||
| References | ||||
|
Adeeko, K.A. and O.O. Ajibola (1990). Processing factors affecting yield and quality of mechanically expressed groundnut oil. Journal of Agricultural Engineering Research 45, pp. 31–43.
AOCS, (1996). The official and tentative methods of the American Oil Chemist's Society, 3rd Ed. American Oil Chemist's Society, 508 South Sixth Street, Champaign, Illinois.
Atwell, W. A. (2001). Wheat Flour. St. Paul, MN: Eagan Press.
Awady , M. N. ( 1978). Tractors and farm machinery ., Txt book ., Col . Ag., Ain Shams U : 146- 167 . (In Arabic)
Beerens, P. (2007). Screw-Ppressing of Jatropha Seeds for Fuelling Purposes in Less Developed Countries. M.Sc. Thesis, Department of Sustainable Energy Technology, Eindhoven University of Technology, Eindhoven, p. 87.
Chancellor, W. J. (1981). Substituting information for energy in agricultural. Trans. ASAE, Paper No. 0001- 2351.
Chouhan, P. M. (1991). Mini oil expellers: new direction to rural oil milling industry - economic feasibility study. Agricultural Engineering Today, 15 (1), 71-76.
Dunford, N. T. (2005). Germ oils from different sources. In: Bailey’s Industrial Oil and Fat Products, 6th Ed. Editor: F. Shahidi. John Wiley and Sons, N.J. Vol. 3, “Edible Oil and Fat Products: Specialty Oils and Oil Products”, Ch. 8, pp. 195-231.
Firestone, D. (1999). Physical and chemical characteristics of oils, fats and waxes, AOCS Press, Champaign, Illinois, pp. 152.
El-Nono, M. A. (2005).Compost pellets made from livestock manure and rice straw. Misr J. Ag. Eng., 22 (1): 237-251.
Hill, S. (1992). Studies on the qualities of soybean oil: Extraction method, soybean type, and soybean stability, Ph.D. Thesis, University of Illinois, Champaign-Urbana, USA. 202 pp.
Ibrahim, M. K. E. (1982). Wet Milling Wheat Grain. Master thesis of science. Fac. of Agric. Mansoura Univ., 64-65.
Kachru, R. P.; P. K. Srivastava; B. S. Bisht; and T. P. Ojha (1986). One hundred bankable post harvest equipments developed in India (pp. 245-252). Bhopal, India: Central Institute of Agricultural Engineering.
MacLeay, I.; K. Harris; and A. Annut (2011). Digest of United Kingdom Energy Statistics 2011. Department of Energy and Climate Change. A National Statistics publication. London: TSO. pp. 321.
Singh, J. and P. C. Bargalo (2000). Development of a small capacity double stage compression screw press for oil extraction. Journal of Food Engineering, 43: 75-82.
Srivastava, A. K.; M. L. Sudha; V. Baskaran; and K. Leelavathi (2007). Studies on heat stabilized wheat germ and its influence on rheological characteristics of dough. Eur Food Res Technol. 224: 365–372
Srivastava, U. K. (1981). Project planning, financing, implementation and evaluation. CMA Monograph No. 95, Indian Institute of Management, Ahamadabad, India.
Tong, W. and A. J. Lawrence (2001). Refining high-free fatty acid wheat germ oil. J. Am Oil Chem. Soc. 78:71-76.
Xiaojun, T. Y. (2002). Stabilization of wheat germ. Chinese Cereals and Oils Association,05.Xie, M. (2009). Aqueous Enzymatic Extraction of Wheat Germ Oil. Master thesis of science. Faculty of the Graduate College of the Oklahoma State University.
Yan-bo, W.U.; D Ying; and X. Bin (2008). Comparative research on the stabilization methods of wheat germ. Science and Technology of Food Industry. 06. | ||||
|
Statistics Article View: 104 PDF Download: 148 |
||||
