STUDY ON SOME OPERATING PARAMETERS AFFECTING THE CUTTING ACTION OF CORN AND COTTON CROPS USING RECIPROCATING MOWER | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 8, Volume 28, Issue 4, October 2011, Page 883-897 PDF (601.62 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2011.102599 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M. M. A. Ali1; M. M. A. Hassan2; G. S. Abd-El-Metaal3 | ||||
| 1Assist. Prof. of Agric. Eng., Fac. of Agric., Zagazig Univ., Egypt. | ||||
| 2Lecturer of Agric. Eng., Fac. of Agric., Zagazig Univ., Egypt. | ||||
| 3Graduate Student of Agric. Eng., Fac. of Agric., Zagazig Univ., Egypt. | ||||
| Abstract | ||||
| The performance of a rear-mounted reciprocating mower was evaluated during cutting two different crop residues, corn and cotton. Some operating parameters were studied in order to select the proper system for cutting crops (optimum forward speed and optimum stalk moisture content). The performance of the reciprocating mower in terms of field efficiency, cutting efficiency, fuel requirements and cutting cost were investigated as a function of change in forward speed, kinematic parameter (ratio of knife peripheral to forward speed) and stalk moisture content. The experimental results revealed that the use of reciprocating mower with maximum cutting efficiency, minimum fuel consumption, energy requirements and criterion cost was achieved under the following conditions: the operating kinematic parameters of 3.6 and 4.3 which corresponded to forward speeds of 4.2 and 4.5 km/h, and knife velocities of 15.12 and 19.44 km/h. The cutting heights of 3.4 and 4.8 cm with stalk moisture contents of 42.19 and 32.11 %, (w. b.) for corn and cotton respectively. | ||||
| References | ||||
|
Awady, M. N. (1978): Engineering of tractors and agricultural machinery, Ch. 13 "Economics of operation for tractors", Arabic Textbk., Col. Agr., Ain-ShamsU.:164-167.
Awady, M. N; E. Y. Ghoniem and A. I. Hashish (1982): Agricultural comparisons between wheat combine harvesters under Egyptian conditions. Res. Bul. Ain shams Univ.:13p.
El-Danasory, M. M. (1984): Intensifying the use of mower under Egyptian condition. M.Sc. Agric. Eng., Faculty of Agriculture, Cairo Univ.Egypt. P. 104-107.
Hanna, G. B; A. E. Suliman; S. M. Younis and A. Z. Taib (1985): Evaluation of different mechanical methods of cotton stalk removal. Misr J. Agr. Eng. 2(1): 3-25.
Hunt, D. (1983): Farm power and machinery management. Iowa state U. press Ames, Iowa, U.S.A.
Ibrahim, A. A. (1998): Comparative study on the performance of reciprocating and rotary mowers in mowing some forage crops. M. Sc. Thesis. Ag. Eng. Dep. Fac. of Ag. Zagazig Univ.Egypt.
Khalil, N. A. (2010): Development of the reciprocating mower for harvesting some cereal crops successfully in small holdings. Ph. D. Thesis Ag. Eng. Dept. Fac. of Ag. Zagazig Univ.Egypt.
Mahrous, A. M. (1995): "Improvement of reciprocating mower efficiency under different crops" M.Sc. Thesis. ZagazigUniv.
Morad, M. M. and T. Z. Fouda (2009): Energy requirements for removing field residues using different equipment. Egyptian J. of Appl. Sci., 24 (3): 390-405.
Yiljep, Y. and U. Mohammad (2005): "Effect of knife velocity on cutting energy and efficiency during impact cutting of sorghum stalk". Agricultural Engineering International: the CIGR EJournal. Manuscript PM 05 004. Vol. VII. December. 2005.
Younis, S. M; G. E. Naser; A. F. Sahrigi and Y. F. Sharobeam (1991): "Performance improvement single and double acting mowers" Misr J. Agric. Eng., 8(4) pp. 285-287. | ||||
|
Statistics Article View: 117 PDF Download: 206 |
||||
