FACTORS AFFECTING THE PERFORMANCE OF AQUATIC FEEDS FLAT-DIE PELLETING MACHINE
Abdel Wahab, M., Tawfik, M., El Shal, A., El Hussiny, Y. (2011). FACTORS AFFECTING THE PERFORMANCE OF AQUATIC FEEDS FLAT-DIE PELLETING MACHINE. EKB Journal Management System, 28(1), 129-148. doi: 10.21608/mjae.2011.105383
M. K . Abdel Wahab; M. A. Tawfik; A. M. El Shal; Y. A. El Hussiny. "FACTORS AFFECTING THE PERFORMANCE OF AQUATIC FEEDS FLAT-DIE PELLETING MACHINE". EKB Journal Management System, 28, 1, 2011, 129-148. doi: 10.21608/mjae.2011.105383
Abdel Wahab, M., Tawfik, M., El Shal, A., El Hussiny, Y. (2011). 'FACTORS AFFECTING THE PERFORMANCE OF AQUATIC FEEDS FLAT-DIE PELLETING MACHINE', EKB Journal Management System, 28(1), pp. 129-148. doi: 10.21608/mjae.2011.105383
Abdel Wahab, M., Tawfik, M., El Shal, A., El Hussiny, Y. FACTORS AFFECTING THE PERFORMANCE OF AQUATIC FEEDS FLAT-DIE PELLETING MACHINE. EKB Journal Management System, 2011; 28(1): 129-148. doi: 10.21608/mjae.2011.105383

FACTORS AFFECTING THE PERFORMANCE OF AQUATIC FEEDS FLAT-DIE PELLETING MACHINE

Misr Journal of Agricultural Engineering
Article 8, Volume 28, Issue 1, January 2011, Page 129-148  XML PDF (1.01 MB)
Document Type: Original Article
DOI: 10.21608/mjae.2011.105383
View on SCiNiTO View on SCiNiTO
Authors
M. K . Abdel Wahab1; M. A. Tawfik2; A. M. El Shal2; Y. A. El Hussiny3
1Professor, Agric. Eng. Dept., Fac. of Agric., Zagazig Univ.,Egypt.
2Lecturer, Agric. Eng. Dept., Fac. of Agric., Zagazig Univ., Egypt.
3Post- graduate student, Agric. Eng. Dept., Fac. of Agric .,Zagazig Univ., Egypt.
Abstract
The overall goal of the present study is evaluating the performance of a local made flat-die pelleting machine to produce a strong and durable aquatic pelleted feeds with minimum cost. Some operating parameters affecting the performance of machine and pellets quality were studied. The flat-die pelleting machine was evaluated under  two values of real hole diameter (4 and 5 mm),three different levels of formula particle size (1, 2 and 3mm), four values of die total thickness (25, 27.5, 30 and 32.5mm), three levels of roller clearance (0.5, 2 and 4mm) and three values of roller teeth width( 4, 6 and 8mm) using constant values of die speed of 300 rpm(4.71m/s), average ration moisture content of 15% (w.b) and hole entry diameter of 9 mm taking into consideration machine production rate, pellets quality (durability, bulk density) pelleting efficiency, specific energy consumption, economical costs of aquatic feed pellets mass and pellet water stability. From the obtained results ,the flat-die pelleting machine could be operate with particle size of 1mm, die total thickness of 32.5mm, roller clearance of 2 mm , roller teeth width of  8mm and real hole diameter of 4 mm to achieve the highest values of  bulk density of 0.915 g/cm3,pellet durability of 95.38%,pelleting efficiency of 95.56%, and pellet water stability of 70% (up to 4 minutes in water) with values of production rate of 107.10 kg/h, consumed energy of 97.95 kW.h/Mg and pelleting total cost of 2386.58 L.E./Mg. Under the same operating conditions, the highest values of bulk density of 0.850 g/cm3,pellet durability of 91.65%,pelleting efficiency of 94.84%, and pellet water stability of 60% (up to 4min.) were recorded at real hole diameter of 5 mm with production rate of 143.65kg/h,consumed energy of 58.41 kW.h/Mg and pelleting total cost of 2374.72 L.E./ Mg.
References
ASAE. 1996. American society of Agricultural Engineers Standards- Engineering practices, and Data, ASAE standard book.

Awady, M.N., I. Yehia, M.T. Ebaid and E.M. Arif. 2003. Development and theory of rice cleaner for reduced impurities and losses. Misr J. Ag. Eng., 20(4) : 53-68.

Dec, R.T.1999. Selection of proper roll press operating parameters. Proceeding of the Institute for Briquetting and Agglomeration (IBA),26:29–36.

Franke, M. and A. Rey. 2006 .Pelleting quality. World Grain:78–90.

Grover, P.D. and S.K. Mishra.1996. Biomass briquetting: technology andpractices. Regional Wood Energy Development Program in Asia, field document no. 46. Bangkok, Thailand: Food and Agriculture Organization of the United Nations (FAO).

Heinemans, H. 1991.The interaction of practical experience and the construction of new pelleting and cooling machinery. Advances in Feed Tech.,6:24–38.

Ibrahim, M. K. 1982. Wet milling of wheat grain. M. Sc. Thesis, Faculty of Agric., Mansoura Univ.,Egypt.

‏Obernberger, I. and G. Thek. 2004. Physical characterization and chemical composition of densified biomass fuels with regard to their combustion behavior. Biomass and Bioenergy : 27:653–69

Thomas, M., D.J. van Zuilichem and A.F. van der Poel.1997. Physical quality of pelleted animal feed. 2. Contribution of processes and its conditions. Animal Feed Science and Technology, 64:173–192.

Turner , R.1995. Bottom line in feed processing: achieving optimum pellet quality. Feed Management;46:30–39.

Statistics
Article View: 206
PDF Download: 325