DEVELOPING THE TRANSMISSION SYSTEM OF THE COMBINE CUTTING DEVICE FOR HARVESTING RICE CROP | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 1, Volume 27, Issue 2, April 2010, Page 426-437 PDF (449.13 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2010.105763 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M. A. Helmy1; T. Z. Fouda2; A. Derbala3; H. A. Kassem4 | ||||
| 1Prof., of Agric. Eng., Fac. of Agric., Kafr-elsheikh U., Egypt. | ||||
| 2Prof., of Agric. Eng., Fac. of Agric., Tanta U., Egypt. | ||||
| 3Assoc. Prof., of Agric. Eng., Fac. of Agric., Tanta U., Egypt. | ||||
| 4Grad. St. Ag. Mec. Dept., Fac. of Agric., Tanta U., Egypt. | ||||
| Abstract | ||||
| The transmission system of the combine cutting device was developed and manufactured from local material to be suitable for the harvesting operation under Egyptian conditions. Performance evaluation of the combine before and after development during the harvesting operation of rice crop was carried out in terms of grain losses, field capacity , field efficiency, fuel consumption, required power, energy, wearing rate, wearing resistance and cost requirements. The combine performance was studied as a function of change in combine forward speed and grain moisture content and operating time. The results were obtained to gave maximum field capacity, field efficiency, wearing resistance and minimum energy, power, fuel consumption wearing rate, and cost requirements for the two systems of the combine cutting device before and after development as following: 1- It is recommended to used the developed combine. 2- The combine forward speed of about 3.5 km/h. 3- The grain moisture content about 23%. | ||||
| References | ||||
|
Abdelmotaleb, I. A.; H. A. El-Gendy and M. A. Hassan (2009). Combine header control. Misr J.of Ag. Eng., 26(3): 1478-1500.
Awady, M. N. (1978). Tractor and farm machinery. Textbook, Faculty of Agriculture, Ain-Shams University.: 164-167.
Badr, M. M. (2005). Comparative study between some different combine sizes in respect to unit plot area. M.Sc. Thesis. Agric. Eng. Dept., Faculty of Agric., Zagazig Univ. Egypt.
El-Hanfy, E. H. and S. A. Shalby (2009). Performance evaluation and modification of the Japanese combine chopping unit. Misr J.of Ag. Eng., 26 (2): 1021-1035.
El-Nakib, A. A; Z. Y. Abdel-Lateef, A. A. El-Messery and A. Khattab (2003). Mechanical harvesting losses in rice crop using combine harvester. Misr J. Ag. Eng., 20 (4): 889-907.
El-Sharabasy, M. M. A. (2006). Construction and manufacture a self propelled machine suits for cutting some grain crops to minimize losses and maximize efficiency. Misr J. Ag. Eng., 23(3):509-531.
Fouda, T. and M. El-Tarhuny (2007). A study on plough shares wearing behavior under conditions of sandy loam soil. Misr J. Ag. Eng., 24(4):831-848.
Habib, R. A.; B. S. Azzam; G. M. Nasr and A. A. Khattab (2001). A theoretical analysis of the " free-cutting process" of plant materials. 1st International conference for Manufacturing Agricultural Equipment and Machinery. 9th Conference of Misr Society of Agric. Eng., 9-11 September.
Hunt, D. (1983). Farm power and machinery management. 8th Ed. Iowa State Univ., Press Ames, Iowa, USA: 364-368.
Kantarc (1982) Abrasive wear in tillage equipment. PhD degree thesis I. T. U. Izmir Univ. Turky المراجع العربیة :وزارة الزراعة (2009). التوصیات الفنیة لمحصول الأرز. مرکز البحوث الزراعیة | ||||
|
Statistics Article View: 257 PDF Download: 236 |
||||
