NUMERICAL INVESTIGATION OF THE EFFICIENT USE OF STIFFENERS IN COLD-FORMED CHANNELS SUBJECTED TO BENDING | ||||
| JES. Journal of Engineering Sciences | ||||
| Article 3, Volume 48, No 3, May and June 2020, Page 383-395 PDF (794.41 K) | ||||
| Document Type: Research Paper | ||||
| DOI: 10.21608/jesaun.2020.107706 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| Ayman R. Hamdallah* ; Ahmad Abdullah | ||||
| Department of civil Engineering, Aswan University, Aswan 81542, Egypt | ||||
| Abstract | ||||
| This paper presents a numerical study to identify the geometrical dimension ratios of the section that make introducing stiffeners to the cold-formed channel sections, subjected to bending, most effective. A V-shape stiffener was introduced to the web and/or the lipped flanges of such sections. A series of nonlinear finite element models has been carried out to investigate the flexural behaviour of the stiffened beam sections. The study shows that introducing stiffener to the web of channel is more effective than if it is used in the compression flange, in terms of increasing the flexural strength and delaying of local and distortional buckling failure modes. However, such effectiveness is not absolute, but it is highly dependent on the geometric properties of the section such as; flange breadth to web height ratio (bf/hw) and web height to its thickness ratio (hw/t). Indeed, considering this finding would help in economic design of such sections and optimal use of material. Keywords: Cold-formed section; Stiffeners; Finite element analyses; bending. | ||||
| Keywords | ||||
| Cold-formed section; Stiffeners; Finite element analyses; bending | ||||
| References | ||||
|
[1] CEN. Eurocode 3: Design of steel structures, Part 1-3: General rules, supplementary rules for cold-formed members and sheeting. European Committee for Standardization, Brussels, 2005.
[2] Hancock GJ, Murray T, Ellifrit DS. Cold-formed steel structures to the AISI specification. New York: Marcel Dekker, Inc.; 2001.
[3] Zhang Y, Wang C, Zhang Z. Tests and finite element analysis of pin-ended channel columns with inclined simple edge stiffeners. Journal of Constructional Steel Research. 2007;63:383-95.
[4] Young B, Chen J. Column tests of cold-formed steel non-symmetric lipped angle sections. Journal of Constructional Steel Research. 2008;64:808-15.
[5] Young B, Yan J. Design of cold-formed steel channel columns with complex edge stiffeners by direct strength method. Journal of Structural Engineering. 2004;130:1756-63.
[6] Zhang J-H, Young B. Compression tests of cold-formed steel I-shaped open sections with edge and web stiffeners. Thin-Walled Structures. 2012;52:1-11.
[7] Young B, Chen J. Design of Cold-Formed Steel Built-Up Closed Sections with Intermediate Stiffeners. Journal of Structural Engineering. 2008;134:727-37.
[8] Wang H, Zhang Y. Experimental and numerical investigation on cold-formed steel Csection flexural members. Journal of Constructional Steel Research. 2009;65:1225-35.
[9] Haidarali MR, Nethercot DA. Local and distortional buckling of cold-formed steel beams with both edge and intermediate stiffeners in their compression flanges. Thin-Walled Structures. 2012;54:106-12.
[10] Li H, Wen Q. Study on distortional buckling performance of cold-formed thin-walled steel flexural Members with stiffeners in the flange. Thin-Walled Structures. 2015;95:161-9.
[11] JunYe, Hajirasouliha I, Becque J, Pilakoutas K. Development of more efficient coldformed steel channel sections in bending. Thin-Walled Structures. 2016;101:1-13.
[12] Wang L, Young B. Design of cold-formed steel channels with stiffened webs subjected to bending. Thin-Walled Structures. 2014;85:81-92.
[13] AISI. North American Specification for the Design of Cold-Formed Steel Structural Members. AISI S100-2016. Washington, D.C.2016.
[14] Schafer B, Sarawit A, Peköz T. Complex edge stiffeners for thin-walled members. Journal of Structural Engineering. 2006;132:212-26.
[15] Schafer BW, Ádány S. Buckling analysis of cold-formed steel members using CUFSM: conventional and constrained finite strip methods. Eighteenth international specialty conference on cold-formed steel structures2006. p. 39-54.
[16] Smith M. ABAQUS/Standard User's Manual, Version 6.14. . Simulia; 2014.
[17] Tohamy SA, Saddek AB, Abdullah A, Hamdallah AR. Numerical performance evaluation of symmetric and unsymmetric stiffeners utilization for cold-formed channels in pure bending. ICCEE2018. Hurghada: Minia University; 2018.
[18] Myers RH, Montgomery DC, Anderson-Cook CM. Response Surface Methodology: Process and Product Optimization Using Designed Experiments: John Wiley & Sons Inc; 2009.
[19] Whitcomb PJ. Design Expert software: Version 11 Stat-Ease, Inc.; 2017.
[20] CEN. Eurocode 3: Design of steel structures, Part 1-5: Plated structural elements. European Committee for Standardization, Brussels, 2005. | ||||
|
Statistics Article View: 231 PDF Download: 498 |
||||
