EFFECT OF PHYSICAL AND ENGINEERING PROPERTIES OF SOME CORN SEEDS VARIETIES ON PNEUMATIC MACHINE PERFORMANCE | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 21, Volume 26, Issue 3, July 2009, Page 1397-1411 PDF (389.21 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2009.108710 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M. Helmy1; A. Derbala2; S. Badr3; S. Shohyieb4 | ||||
| 1Prof. of Ag., Eng., Kafrelsheikh Univ., Egypt | ||||
| 2Lecturer of Ag., Eng., Tanta Univ., Egypt, | ||||
| 3Senior Res., Ag., Res., Center, Dokki, Giza, Egypt | ||||
| 4Post-Grad., Student, Ag. Res., Center, Dokki, Giza, Egypt | ||||
| Abstract | ||||
| A series of experiments were carried out during seasons 2005/2007 at Gemmiza Agricultural Research Station, Tanta, El–Gharbia Governorate, Egypt. The objectives of these experiments were to study the effect of some physical and engineering properties of some Egyptian varieties of corn on the performance of the pneumatic drill machine. The results indicated that, the maximum values of the physical and engineering properties were in case of corn TC 310. But the minimum values were in case of corn ryana. At the same time, the moderate values were in case of corn SC 10. On the other hand, the levels of tractor speed which give the conformity fan air speed with suction air velocity and lowest value of fuel consumption were determined. The results showed that, the fan air speeds were 225, 249 and 247 r.p.m under corn ryana, SC 10 and TC 310, respectively. The fuel consumption rates were 3.4, 3.7 and 3.9 l/h in case of corn ryana, SC 10 and TC 310, respectively. From the obtained data the study recommended that, the suitable diameter seed plate holes were 7, 7 and 5 mm for corn SC 10, TC 310 and ryana, respectively. Also, the optimum suction air speeds were 12, 14 and 15 m/s for corn ryana, SC 10 and TC 310, respectively. Whereas, the highest percent of seeds holding in seed plate holes were obtained at these speeds. On the other hand, the appropriate operating speed of tractorwas 3 km/h. | ||||
| References | ||||
|
El–Nakib, A. A. (1975). Studies on mechanization of maize planting. M.Sc., Thesis, Ag. Eng., Faculty of Agric. Al-Azhar Univ., pp.1–72.
El-Sahrigi, A. F. and A.Y. Korayem (1988). Aerodynamic properties of chopped straw of wheat stalks of Giza 157. Misr J. of Ag. Eng., 5(2):112–118.
Garratt, R. E. and D. B. Brooker (1965). Aerodynamic drag of farm seeds. Transactions of the ASAE, 8(1):49–52.
Helmy, M. A. (2002). The determination of porosity rate on the different moisture content of several crops. Misr J. of Ag. Eng. 5(11):216–222.
Ibrahim, M. A. (1992). Design an apparatus suitable for winnowing and separating wheat products from stationery threshers. M.Sc., Thesis, Faculty of Agric. Alex. Univ.
Kaleem, F. H.; Z. E. Ismail and G. R. Abd–Hakim (1993). Factors affecting seed cleaning efficiency. Part 1: Seed straw mixture and characteristics, Misr J. of Ag. Eng., 10(2):369–382.
Matouk, A. M.; S. M. Radwan; M. M. El–Kholy and T. R. Ewies (2004). Determination of seeds density and porosity for some cereal crops. Misr J. of Ag. Eng., 21(3):623–641.
Nimkar, P. M. and P. K. Hattopadhyay (2001). Some physical properties of green gram. J. of Ag. Eng. Res. 80(2):183–189.
Nonami, S. k. and S. O. Nelson (2002). Dimensional and density data for seeds of cereal seed and other crops. Transactions of the ASAE, 45(1):165–170.
Santall, G. W. and K. N. Mascheroni (2003). Aerodynamic properties of sunflower seeds. J. of Ag. Eng. Res., 19(22):436–401.
Sitkei, G. W. (1986). Mechanics of Agricultural materials. Elsevier Sc. Pub. Amsterdam–Oxford–New York–Tokyo. 294–301. | ||||
|
Statistics Article View: 117 PDF Download: 142 |
||||
