Effect of space holder percent on the porosity biocompatibility of nano Ti foam by PM technique | ||||
| International Journal of Materials Technology and Innovation | ||||
| Article 6, Volume 1, Issue 1, June 2021, Page 45-51 PDF (1.3 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/ijmti.2021.181119 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
M. A. Khater1; M. T. Elwakad2; O. A. El-kady3; A S. eldesoky  4
| ||||
| 1Department of Biomedical Engineering, Faculty of Eng., Helwan Univ, Cairo, Egypt. | ||||
| 2Faculty of Eng. & Technology, Future Univ, 5th settlement, Cairo, Egypt. | ||||
| 3Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt. | ||||
| 4Department of Biomedical Engineering, Higher Technological Institute, 10th of Ramadan, 228, Egypt. | ||||
| Abstract | ||||
| Powder metallurgy (PM) approach was utilized for the preparation of Ti porous material mixed mechanically with different percentages of sodium chloride salt from 10 to 40 % with stirring speed 100 rpm and ball to powder ratio 10:1 for milling time 24 h. The Ti –NaCl mixed samples were compacted under 600Mpa, then sintered at 1450 ᴼC for 90 min in a vacuum furnace. The phase composition and microstructure of Ti samples are investigated through X-ray diffraction analysis and scanning electron microscope (SEM). All the prepared samples were characterized by measuring the porosity percentage, Vickers hardness, and compression strength. Microstructure indicated that porosity was found to increase with increasing salt percent while the highest hardness (380) and the compression strength (45MPa) were recorded for the lowest ratio of salt (10%NaCl). Biocompatibility test was estimated for the prepared samples, which exhibited the high viability for cell with good growth of the life cells on the sample’s surface, and low adhesion. | ||||
| Keywords | ||||
| Biocompatibility; Mechanical properties; Powder Metallurgy; Porous Titanium; Medical applications | ||||
| References | ||||
|
[1] Q. Chen, GA. Thouas. Metallic implant biomaterials, Materials Science and Engineering, 87 (2015) 1-57, doi: 10.1016/j.mser.2014.10.001.
[2] K. Shemtov-Yona and D. Ritter. On the mechanical integrity of retrieved dental implants, J. Mech. Behav. Biomed. Mater: Rep., 49 (2015) 290–299. doi; 10.1016/j.jmbbm.2015.05.014.
[3] K.J. Franz and A.F. Hehmeyer. Introduction: Metals in Medicine, Chem. Rev. 119(2019) 727−729, DOI: 10.1021/acs.chemrev.8b00685
[4] K. Dabrowia, .C. James . Metals in Medicine, Inorganic Chemica Acta. 393(2012) 1-2, doi.10.1016/j.ica.2012.07.022.
[5] I. Gotman. Characteristics of Metals Used in Implants, Journal of Endourology, 11(1998) 383-389, doi: 10.1089/end.1997.11. 383.
[6] J. M. Calderon-Moreno et al. Microstructural and mechanical properties, surface and electrochemical characterization of a new Ti--Zr--Nb alloy for implant applications, Journal of Alloys and Compounds, 612(2014) 398-410, doi: 10.1016/j.jallcom.2014.05.159
[7] A.D. Marter, A.S. Dickinson, F. Pierron, et al. A Practical Procedure for Measuring the Stiffness of Foam like Materials, Experimental Techniques 42 (2018) 439–452, doi. 10.1007/s40799-018-0247-0
[8] S S Sharma, Y S Rajpoot. Development of aluminum metal foam using blowing agent, IOP Conference Series: Materials Science and Engineering, 377 (2018), doi:10.1088/1757-899X/377/1/012150.
[9] S. Ahmad, N. Muhamad, J. Sahari, et al. Characterisation of Titanium Foams Sintered at Different Temperatures Prepared by the Slurry Method, Sains Malaysiana; Journal, 39 (2010) 77-82.
[10] M. Geetha, A. K. Singh, R. Asoka Mani, and A. K. Gogia. Ti based biomaterials, the ultimate choice for orthopedic implants--a review, Prog. Mater. Sci., 54 (2009) 397-425, doi: 10.1016/j.pmatsci.2008.06.004.
[11] A. Chouhan, Synthesis and Characterization of Ti-foam using NaCl as space holder, Department of Biotechnology & Medical Engineering, National Institute of Technology Rourkela, 2015.
[12] CE WEN. Novel titanium foam for bone tissue engineering, Journal of Materials Research, 17(2002) 2633 – 2639, doi. 10.1557/JMR.2002.0382.
[13] Y. xuezheng. Mechanical Properties of Titanium Foams Having Disordered and Ordered Cell Structures, Tokyo Metropolition University, 2017.
[14] I. Braceras, J.I.Onate, L.Goikoetxea, J.L.Viviente, J.I.Alava, and M.A.de Maeztu, Bone cell adhesion on ion implanted titanium alloys, Surface and Coatings Technology journal. 196 (2005) 321-32, doi. 10.1016/j.surfcoat.2004.08.201
[15] A. R. Selfridge. Approximate material properties in isotropic materials, IEEE Xplore, ,32(1985) 381–394, doi. 10.1109/ T-SU.1985.31608.
[16] M. Giner, E. Chicardi, A. Costa. Et al; Biocompatibility and Cellular Behavior of TiNbTa Alloy with Adapted Rigidity for the Replacement of Bone Tissue, Metals, MDPI, 130 (2021) 1-14. doi. 10.3390/met110101302021.
[17] A.A. Khalili and M.R. Ahmad. A Review of Cell Adhesion Studies for Biomedical and Biological Applications, Int. J. Mol. Sci. 16(2015) 18149–18184, doi: 10.3390 / ijms160818149
[18] O. El-Kady, and A. Fathy. Effect of SiC particle size on the physical and mechanical properties of extruded Al matrix Nano composites, Materials & Design, 54(2014) 348-353, doi. /10.1016/j.matdes.2013.08.049
[19] A. Manonukul . P. Srikudvien and M. Tange, Microstructure and Mechanical Properties of Commercially Pure Titanium Foam with Varied Cell Size Fabricated by Replica Impregnation Method, Materials Science & Engineering A. 650(2016) 432-437. .doi.10.1016/j.msea.2015.10.074.
[20] M. E. Dizlek, M. Guden, et al. Processing and compression testing of Ti6Al4V foams for biomedical applications, Journal of Materials Science, 44(2009) 1512–1519, doi 10.1007/s10853-008-3038-7
[21] M.Y. Zakaria, M.I. Ramli, A.B. Sulong, N.Muhamad, M.H. Ismail. Application of sodium chloride as space holder for powder injection molding of alloy Titanium- Hydroxyapatite composites, Journal of Materials Research and Technology, 12(2021) 478-482, doi. 10.1016/j.jmrt.2021.02.087.
[22] T. Matsushit. S. Fujibayash. T. Kokubo, Titanium foam for bone tissue engineering, Metallic Foam Bone. 11(2017) 111-130, doi.10.1016/B978-0-08-101289-5.00004-4.
[23] S. Kaur, K. Ghadirinejad and R.H. Oskouei, An Overview on the Tribological Performance of Titanium Alloys with Surface Modifications for Biomedical Applications, lubricants 65 (2019) 1-15, doi: 10.3390/ lubricants7080065.
[24] J.W. Nicholson. Titanium Alloys for Dental Implants: A Review, prosthesis, MPDI, 2(2020) 100–116; doi: 10.3390/ prosthesis2020011.
[25] D. P. Mondal, M. Patel, S.Das, A.K.Jha, G.Gupt, S.B.Ary,Titanium foam with coarser cell size and wide range of porosity using different types of evaporative space holders through powder metallurgy, Materials & Design, 63 (2014) 89-99, doi. 10.1016/ j. matdes.2014.05.054
[26] O. Cetinel, Z. Esen and B. Yildirim. Fabrication, Morphology Analysis, and Mechanical Properties of Ti Foams Manufactured Using the Space Holder Method for Bone Substitute Materials, Metals, MDPI, 9-340(2019); doi: 10.3390/ met9030340 | ||||
|
Statistics Article View: 331 PDF Download: 485 |
||||
