Studying the Effect of Process Controlling Agent on the Microstructure, Electrical and Thermal Conductivities of Copper /Graphene Composite Prepared by PM
Hamed, A., Mosa, E., Mahdy, A., El-batanony, I., Alkady, O. (2021). Studying the Effect of Process Controlling Agent on the Microstructure, Electrical and Thermal Conductivities of Copper /Graphene Composite Prepared by PM. EKB Journal Management System, 1(1), 89-95. doi: 10.21608/ijmti.2021.181127
A. T Hamed; E. S. Mosa; A. A. Mahdy; I. G. El-batanony; O. A. Alkady. "Studying the Effect of Process Controlling Agent on the Microstructure, Electrical and Thermal Conductivities of Copper /Graphene Composite Prepared by PM". EKB Journal Management System, 1, 1, 2021, 89-95. doi: 10.21608/ijmti.2021.181127
Hamed, A., Mosa, E., Mahdy, A., El-batanony, I., Alkady, O. (2021). 'Studying the Effect of Process Controlling Agent on the Microstructure, Electrical and Thermal Conductivities of Copper /Graphene Composite Prepared by PM', EKB Journal Management System, 1(1), pp. 89-95. doi: 10.21608/ijmti.2021.181127
Hamed, A., Mosa, E., Mahdy, A., El-batanony, I., Alkady, O. Studying the Effect of Process Controlling Agent on the Microstructure, Electrical and Thermal Conductivities of Copper /Graphene Composite Prepared by PM. EKB Journal Management System, 2021; 1(1): 89-95. doi: 10.21608/ijmti.2021.181127

Studying the Effect of Process Controlling Agent on the Microstructure, Electrical and Thermal Conductivities of Copper /Graphene Composite Prepared by PM

International Journal of Materials Technology and Innovation
Article 8, Volume 1, Issue 1, June 2021, Page 89-95  XML PDF (425.2 K)
Document Type: Original Article
DOI: 10.21608/ijmti.2021.181127
View on SCiNiTO View on SCiNiTO
Authors
A. T Hamed email 1; E. S. Mosa2; A. A. Mahdy2; I. G. El-batanony3; O. A. Alkady4
1PHD student,15th of May Higher Institute of Engineering
2Mining, Metallurgy and Petroleum Engineering Department, Faculty of Engineering, AL-Azhar University, Cairo, Egypt
3Mechanical Engineering Dept., Faculty of Engineering, Al-Azhar University, Cairo, Egypt
4Manufacturing Technology Department, Central Metallurgical Research and Development Institute (CMRDI), Cairo, Egypt
Abstract
Copper-graphene composite is prepared with 0.25,0.50,0.75,1.00,1.25 and 1.50 wt.% graphene.  Powder metallurgy technique is used for the preparation process. In which copper powder is mechanically milled with graphene nanosheets (GNSs) by 10: 1 ball to powder ratio, and 400 rpm for 12 hr milling time. The mixtures are compacted by a uniaxial press under 700 Mpa pressure. The compacted samples are sintered under a controlled atmosphere at 950 oC for 1.5 hrs. A comparison between methanol & hexane as a process control agent is established. The effect of both on the microstructure, electrical and thermal conductivities of the prepared Cu /graphene nanocomposites is studied. All results indicated that hexane samples have a more homogeneous microstructure with low porosity. For the two groups (Hexane and Methanol group samples), the density was decreased gradually by increasing the graphene percentage. The results indicated that both the electrical and thermal conductivities decrease by increasing graphene content. 1wt. % graphene sample has the most homogenous microstructure, while, 0.25 wt. % graphene is the most one for the methanol group samples. Generally, all results indicated that hexane is the better PCA than methanol.
Keywords
Copper composites; Graphene; Mechanical alloying; Process control agent (PCA); Electrical conductivity
References
[1] S. C. Tjong. Recent progress in the development and properties of novel metal matrix nanocomposites reinforced with carbon nanotubes and graphene nanosheets. Mater Sci Eng R. 74,( 2013), P. 281–350.

[2] S. R. Bakshi. Carbon nanotube reinforced metal matrix composites—a review. Int Mater Rev 55(2010) , P. 41–64.

[3] C. Suryanarayana, Mechanical alloying and milling, Prog Mater Sci 46(2010) 1–184

[4] H. Yue, L. Yao. Effect of ball-milling and graphene contents on the mechanical properties and fracture mechanisms of graphene nanosheets reinforced copper matrix composites. J Alloys Comp. 691, (2017) 755–762.

[5] P.H. Manrique, Copper/graphene composites: a review, J Mater Sci, 54(2019) 12236–12289.

[6] D. Parobek, H. Liu. Wettability of graphene, 2D Mater. 2 (2015), 032001.

[7] A. Fathy a, Omyma El-Kady. Thermal expansion and thermal conductivity characteristics of Cu–Al2O3, nanocomposites. Materials & Design, 46 (2013) 355-359.

[8] H. Saad. Effect of Carbon Nano Tubes (CNT) and Silicon Carbide (SiC) on Mechanical Properties of Pure Aluminium Manufactured by Powder Metallurgy. Journal of Materials Research and Technology, 9 (2019) 1948-1954.

[9] Y .Cui, L Wang, Li B, Cao G, Fei W. Effect of ball-milling on the defeat of few-layer graphene and properties of copper matrix composites. Acta Metall Sin Eng Let t. 27, (2014) 937–943.

[10] K. Jagannadham. Volume fraction of graphene platelets in copper–graphene composites. Metall Mater Trans A, 44 (2013)  552–559.

[11] Khobragade, N., Kumar, B., Bera, S., & Roy, D. Studies on graphene reinforced Cu base composites prepared by two step thermal processing method. Materials Today: Proceedings, 4(8). (2017) 8045–8051

[12] M.M. Mohammed, A. Fathy, O. .El-Kady. Effect of Al2O3 addition on hardness and wear behavior of Cu–Al2O3 electro-less coated Ag nanocomposite   Journal of Materials Research and Technology, 9,  (2020) 5024-5033.

[13] H. M. Yehia, A. Abu-Oqail, Maher, A. Elmaghraby, O. El-kady. Microstructure, hardness, and tribology properties of the (Cu/MoS2)/graphene nanocomposite via the electroless deposition and powder metallurgy technique. J of Composite Mater. 54, (2020) 3435-3446.

Statistics
Article View: 236
PDF Download: 346