EFFECTS OF WELDING PARAMETERS ON CHARACTERIZATION AND MECHANICAL PROPERTIES OF STEEL 37 WELDMENTS | ||||
| JES. Journal of Engineering Sciences | ||||
| Article 3, Volume 48, No 2, March and April 2020, Page 212-221 PDF (823.39 K) | ||||
| Document Type: Research Paper | ||||
| DOI: 10.21608/jesaun.2020.188012 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
Mohamed M. Ali  ; Moatasem M. Khalifa
| ||||
| Mining and Metallurgical Dept. Faculty of Engineering, Al-Azhar University, Qena- Egypt | ||||
| Abstract | ||||
| Effects of welding parameters on the characterization and mechanical properties of steel 37 weldments were investigated on a single V-shaped groove weld joint. These parameters are; type of electrode, welding current, welding speed, and type of used arc welding and plate thickness. Radiography, metallography and mechanical testing were carried out for the steel 37 weldments. Results indicated that as the heat input increased, the welding current and plate thickness increased but the welding speed decreased. The grains of the base metal, heat affected zoon (HAZ), root and cap were changed in size and phases in these locations. Radiography showed that no defects were found. The average hardness values were 173 HB at base metal, 175 HB at the HAZ, 180 HB at the cap and 133 HB at the root, respectively. Yield strength, ultimate tensile strength and elongation of the welded steel 37 were in the range between 374 and 425 MPa, between 542 and 606 MPa and in the range between 34.6 and 37.5 %, respectively. Such values tend to increase with increasing the current and heat input and decreasing the plate thickness. The chemical and mechanical properties of the welded electrodes proved to influence the efficiency of the welding process. The best welding results were obtained with current 75 A at the root, 130 A at the cap and welding speed of 1.3 mm/s in the root and 2 mm/s in the cap. | ||||
| Keywords | ||||
| Steel 37; Weldments; Welding variables; Hardness; Tensile strength; Elongation | ||||
| References | ||||
|
[1] Rohit Jha, A. K. Jha, (2014), "Investigating the effect of welding current on the tensile properties of SMAW welded mild steel joints", International Journal of Engineering Research & Technology (IJERT), Vol. 3 (issue 4), pp. 1304 - 1307.
[2] Gopal Krushna mohanta and Ajit kumar Senapati, (2018), "The effect of welding parameter on Mild steel by MMAW", IOP Conf. Series: Materials Science and Engineering 410 doi:10.1088/1757-899X/410/1/012015 pp. 1304 - 1307.
[3] Deepak kamra, Amandeep singh and Harpreet singh, (2015), "Microstructure analysis of shielded metal arc welding using different electrode combination", International Journal for Technological Research in Engineering (IJTRE), Vol. 2 (issue 7), pp. 1138 - 1142.
[4] S.P. Tewari, A. Gopta and J. Prakash, (2010), "Effect of welding parameters on weldability of materials", International Journal of Engineering Science and Technology, Vol. 2 (issue 4), pp.512-516.
[5] Ashish Thakur, Hagos Gebrelibanos and Tadesse Gabrey, (2019), "Arc Welding Process Selection through a Quality and Costs", International Journal of Current Engineering and Technology, Vol.9, No.3, pp. 383-394.
[6] P. Kumari, K. Archna and R.S. Parmar, (2011), "Effect of welding parameters on weld bead geometry in MIG welding of low carbon steel", International Journal of Applied Engineering Research, Vol. 6 (issue 2), pp.249-258.
[7] Cynthia L. Jenney Annette O'Brien, (2007), "Welding Handbook", Ninth Edition Vol. 3, Welding process part 2 technology, Miami, America welding society
[8] Zakaria Boumerzoug, Chemseddine Derfouf and Thierry Baudin, (2010)," Effect of Welding on Microstructure and Mechanical Properties of an Industrial Low Carbon Steel", Engineering, Vol 2, pp. 502-506.
[9] Anil Parmar and Aakash Dubey, (2017) ''Study of heat affected zone for SMAW process for low carbon steel specimen with controlled parameters'', International Journal of Modern Trends in Engineering and Research (IJMTER) Vol. 4(issue 11), pp. 23-28.
[10] https://www.makeitfrom.com/material-properties/ASTM-A283-Grade-A-Carbon-Steel, 2019.
[11] Welding procedure guide- An easy to follow guide covering the preparation of welding procedure data sheets", September 2008 CWB Group - Industry Services.
[12] ASTM E8 / E8M-13, (2013),"Standard test methods for tension testing of metallic materials", ASTM International, West Conshohocken, PA, www.astm.org
[13] A L Dhobale and H K Mishra, (2015), "Review on effect of heat input on tensile strength of butt weld joint using MIG welding" International Journal of Innovations in Engineering Research and Technology (IJIERT), Vol. 2 (issue 9), pp. 1-13.
[14] Mohd. Suhail, Mohd. Faizan Hasan and P. K. Bharti, (2014), "Effect of welding speed, current and voltage on mechanical properties of underwater welded mild steel specimen (C,Mn, Si) with insulated electrode E6013", MIT International Journal of Mechanical Engineering, Vol.4(issue 2), pp. 120-124.
[15] H.R. Ghazvinloo, A. Honarbakhsh- Raouf and N. Shadfar, (2010), "Effect of arc voltage, welding current and welding speed on fatigue life, impact energy and bead penetration of AA 6061 joints produced by robotic MIG welding", Indian Journal of Science and Technology. Vol. 3(issue 2), pp. 156-162. | ||||
|
Statistics Article View: 234 PDF Download: 769 |
||||
