The Effect of the Rate of Strain on the Thermal and Mechanical Properties of Al- 6030 Processed by ECAP.
Mohamed, M., Nabil Zaafarani, N., E. Kabeel, A. (2021). The Effect of the Rate of Strain on the Thermal and Mechanical Properties of Al- 6030 Processed by ECAP.. EKB Journal Management System, 46(4), 1-6. doi: 10.21608/bfemu.2021.208215
maher Rashad Mohamed; Nader Nabil Zaafarani; A. E. Kabeel. "The Effect of the Rate of Strain on the Thermal and Mechanical Properties of Al- 6030 Processed by ECAP.". EKB Journal Management System, 46, 4, 2021, 1-6. doi: 10.21608/bfemu.2021.208215
Mohamed, M., Nabil Zaafarani, N., E. Kabeel, A. (2021). 'The Effect of the Rate of Strain on the Thermal and Mechanical Properties of Al- 6030 Processed by ECAP.', EKB Journal Management System, 46(4), pp. 1-6. doi: 10.21608/bfemu.2021.208215
Mohamed, M., Nabil Zaafarani, N., E. Kabeel, A. The Effect of the Rate of Strain on the Thermal and Mechanical Properties of Al- 6030 Processed by ECAP.. EKB Journal Management System, 2021; 46(4): 1-6. doi: 10.21608/bfemu.2021.208215

The Effect of the Rate of Strain on the Thermal and Mechanical Properties of Al- 6030 Processed by ECAP.

MEJ- Mansoura Engineering Journal
Article 23, Volume 46, Issue 4, December 2021, Page 1-6  XML PDF (737.11 K)
Document Type: Research Studies
DOI: 10.21608/bfemu.2021.208215
View on SCiNiTO View on SCiNiTO
Authors
maher Rashad Mohamed email orcid 1; Nader Nabil Zaafarani2; A. E. Kabeel3
1Assistant Professor of Production Engineering and Mechanical Design Department, Faculty of Engineering, Tanta University
2Assistant Professor of Production Engineering and Mechanical Design Department, Faculty of Engineering, Tanta University, Egypt
3Professor of Mechanical Power Engineering Department, Faculty of Engineering, Tanta University, Egypt and Faculty of Engineering, Delta University for Science and Technology, Egypt
Abstract
The function of severe plastic deformation (SPD) rate during equal-channel angular pressing (ECAP) on the thermal and mechanical characteristics of the aluminum alloy 6030 are experimentally investigated. ECAP was carried out at room temperature onto refining grain size for Al- 6030 of square cross-section specimens.  The tests show that, for decreasing the rate of strain from 0.016 to 0.0023 s-1, the improvement in the hardness increases gradually until the highest value is reached at the rate of strain 0.004 s-1and decreases after that gradually. The percentage improvement in the hardness is around 68 % at the rate of strain 0.004 s-1. The ECAP process improves the yield strength of aluminum alloy 6030 by 222 % on average at the rate of strain 0.004 s-1. Also, for decreasing the rate of strain from 0.016 to 0.0023 s-1 the thermal conductivity increases gradually to the maximum value 137.5 W/m° K at rate of strain 0.004 s-1and decrease after that gradually. The ECAP process improves the thermal conductivity by 4.88 % for the rate of strain 0.004 s-1 as compared to the case without ECAP process. From the present experimental results, the optimum rate of strain is 0.004 s-1 to obtain the optimal thermal and mechanical properties of the aluminum alloy 6030 during the ECAP processing.
Keywords
ECAP; Al-6030; Hardness; Strain rate; Thermal conductivity, Optimum properties
Statistics
Article View: 134
PDF Download: 189