Marginal and internal fit evaluation of metal copings fabricated by selective laser sintering and CAD/CAM milling techniques: in-vitro study
Abdelhafiz, S., Abdelkader, S., Azer, A. (2022). Marginal and internal fit evaluation of metal copings fabricated by selective laser sintering and CAD/CAM milling techniques: in-vitro study. EKB Journal Management System, 47(2), 134-139. doi: 10.21608/adjalexu.2021.53797.1139
Shimaa H. Abdelhafiz; Sanaa H. Abdelkader; Amir Azer. "Marginal and internal fit evaluation of metal copings fabricated by selective laser sintering and CAD/CAM milling techniques: in-vitro study". EKB Journal Management System, 47, 2, 2022, 134-139. doi: 10.21608/adjalexu.2021.53797.1139
Abdelhafiz, S., Abdelkader, S., Azer, A. (2022). 'Marginal and internal fit evaluation of metal copings fabricated by selective laser sintering and CAD/CAM milling techniques: in-vitro study', EKB Journal Management System, 47(2), pp. 134-139. doi: 10.21608/adjalexu.2021.53797.1139
Abdelhafiz, S., Abdelkader, S., Azer, A. Marginal and internal fit evaluation of metal copings fabricated by selective laser sintering and CAD/CAM milling techniques: in-vitro study. EKB Journal Management System, 2022; 47(2): 134-139. doi: 10.21608/adjalexu.2021.53797.1139

Marginal and internal fit evaluation of metal copings fabricated by selective laser sintering and CAD/CAM milling techniques: in-vitro study

Alexandria Dental Journal
Article 6, Volume 47, Issue 2, August 2022, Page 134-139  XML PDF (460.26 K)
Document Type: Original Article
DOI: 10.21608/adjalexu.2021.53797.1139
View on SCiNiTO View on SCiNiTO
Authors
Shimaa H. Abdelhafiz email orcid 1; Sanaa H. Abdelkaderorcid 2; Amir Azerorcid 3
1Conservative Department, Fixed Prosthodontics division, Faculty of Dentistry, Alexandria University, Alexandria, Egypt.
2Professor, Department of Conservative Dentistry, Fixed Prosthodontics division, Faculty of Dentistry, Alexandria University.
3Associate Professor, Department of Conservative Dentistry, Fixed Prosthodontics division, Faculty of Dentistry, Alexandria University.
Abstract
Introduction: Metal-ceramic restorations are still commonly used in dentistry. The success of these restorations depends mainly on the marginal integrity and the internal fit which in turn is affected by the technique of fabrication.
Aim of the study: Comparing the marginal and internal fit of metal copings manufactured using three different techniques.
Materials and method: A metal master die simulating a maxillary first molar preparation was fabricated. Thirty Vinyl poly siloxane impressions were prepared for the master die and poured to obtain 30 epoxy resin dies. The epoxy dies were allocated at random to 3 groups (n=10) following the method of metal copings fabrication. Group I: selective laser sintering technique (additive technique), group II: CAD-CAM milling technique (subtractive technique), group III: lost wax technique (control group). The marginal and internal fit was evaluated by the silicone replica technique. The data were analyzed by One Way ANOVA followed by multiple pairwise comparisons using Bonferroni adjustment.
Results: Group II had a significantly larger internal gap (33.60 µm) compared to group I (30.15 μm) and group III (27.83 μm) (P=0.03). No significant difference was found in the marginal fit.
Conclusions: Although Metal copings produced by the lost wax technique showed the best adaptation, all tested techniques resulted in clinically acceptable fit values.
Keywords
Marginal fit; internal fit; selective laser sintering; and CAD-CAM
Statistics
Article View: 223
PDF Download: 484