Internal Adaptation and Marginal Gap of Split-File Versus Scanned Workflows of Three Types of Non-Metallic Super-Structures on Zirconia Abutments
Elbanna, K., Alqutub, A. (2022). Internal Adaptation and Marginal Gap of Split-File Versus Scanned Workflows of Three Types of Non-Metallic Super-Structures on Zirconia Abutments. EKB Journal Management System, 68(2), 1655-1664. doi: 10.21608/edj.2022.117767.1962
Khaled Elbanna; Alaa Alqutub. "Internal Adaptation and Marginal Gap of Split-File Versus Scanned Workflows of Three Types of Non-Metallic Super-Structures on Zirconia Abutments". EKB Journal Management System, 68, 2, 2022, 1655-1664. doi: 10.21608/edj.2022.117767.1962
Elbanna, K., Alqutub, A. (2022). 'Internal Adaptation and Marginal Gap of Split-File Versus Scanned Workflows of Three Types of Non-Metallic Super-Structures on Zirconia Abutments', EKB Journal Management System, 68(2), pp. 1655-1664. doi: 10.21608/edj.2022.117767.1962
Elbanna, K., Alqutub, A. Internal Adaptation and Marginal Gap of Split-File Versus Scanned Workflows of Three Types of Non-Metallic Super-Structures on Zirconia Abutments. EKB Journal Management System, 2022; 68(2): 1655-1664. doi: 10.21608/edj.2022.117767.1962

Internal Adaptation and Marginal Gap of Split-File Versus Scanned Workflows of Three Types of Non-Metallic Super-Structures on Zirconia Abutments

Egyptian Dental Journal
Article 15, Volume 68, Issue 2 - Serial Number 4, April 2022, Page 1655-1664  XML PDF (1.11 MB)
Document Type: Original Article
DOI: 10.21608/edj.2022.117767.1962
View on SCiNiTO View on SCiNiTO
Authors
Khaled Elbanna email 1; Alaa Alqutuborcid 2
1Assistant Professor, Fixed Prosthodontics Division, Department of Oral and Maxillofacial Surgery and Diagnostic Sciences, Faculty of Dentistry, Umm Al-Qura University, KSA
2Assistant Professor, Implantology Division, Department of Oral and Maxillofacial Surgery and Diagnostic Sciences, Umm Al-Qura University, KSA
Abstract
The aim of this study was to compare marginal and internal adaptation of non-metallic implant supported crowns fabricated using split-file and scanning workflows. Materials and methods: A total of 30 crowns were fabricated and divided into two equal groups: Group I: where the master abutment was used virtually as a split-file workflow and Group II where the master abutment was scanned. Each group was subdivided into three equal subgroups according to material: subgroup A: zirconia, B: lithium disilicate, and C: polyetherketoneketone (PEKK). Margin and internal adaptation were evaluated using replica technique with a digital microscope. Results: Group II had lower marginal and internal gap means (71.55, 94.66 µm respectively) than Group I (85.44, 103.73 µm respectively). Zirconia had better margin and internal adaptation (69.27, 82.48 µm respectively) followed by PEKK (82.14, 105.4 µm respectively) then lithium disilicate which had the largest margin and internal gaps (84.08, 109.7 µm respectively). Conclusions: 1. Despite the better fit of the scanned abutment group, split-file technique has shown acceptable marginal and internal adaptation. 2. Milled zirconia showed better fit than PEKK and lithium disilicate, however the three materials had acceptable marginal and internal adaptation.
Keywords
Split-File; Internal Adaptation; Margin gap; Zirconia; PEKK
Statistics
Article View: 142
PDF Download: 137