HEAT TRANSFER TO A TANGENTIALLY INJECTED SWIRL FLOW THROUGH AN ARTIFICIALLY ROUGHENED ANNULUS
ABDEL-MONEIM, S., EL-SHAMY, A., BERBISH, N. (2001). HEAT TRANSFER TO A TANGENTIALLY INJECTED SWIRL FLOW THROUGH AN ARTIFICIALLY ROUGHENED ANNULUS. EKB Journal Management System, 9(ASAT Conference, 8-10 May 2001), 1-18. doi: 10.21608/asat.2001.24852
S. A. ABDEL-MONEIM; A. R. EL-SHAMY; N. S. BERBISH. "HEAT TRANSFER TO A TANGENTIALLY INJECTED SWIRL FLOW THROUGH AN ARTIFICIALLY ROUGHENED ANNULUS". EKB Journal Management System, 9, ASAT Conference, 8-10 May 2001, 2001, 1-18. doi: 10.21608/asat.2001.24852
ABDEL-MONEIM, S., EL-SHAMY, A., BERBISH, N. (2001). 'HEAT TRANSFER TO A TANGENTIALLY INJECTED SWIRL FLOW THROUGH AN ARTIFICIALLY ROUGHENED ANNULUS', EKB Journal Management System, 9(ASAT Conference, 8-10 May 2001), pp. 1-18. doi: 10.21608/asat.2001.24852
ABDEL-MONEIM, S., EL-SHAMY, A., BERBISH, N. HEAT TRANSFER TO A TANGENTIALLY INJECTED SWIRL FLOW THROUGH AN ARTIFICIALLY ROUGHENED ANNULUS. EKB Journal Management System, 2001; 9(ASAT Conference, 8-10 May 2001): 1-18. doi: 10.21608/asat.2001.24852

HEAT TRANSFER TO A TANGENTIALLY INJECTED SWIRL FLOW THROUGH AN ARTIFICIALLY ROUGHENED ANNULUS

International Conference on Aerospace Sciences and Aviation Technology
Article 43, Volume 9, ASAT Conference, 8-10 May 2001, May 2001, Page 1-18  XML PDF (2.75 MB)
Document Type: Original Article
DOI: 10.21608/asat.2001.24852
View on SCiNiTO View on SCiNiTO
Authors
S. A. ABDEL-MONEIM1; A. R. EL-SHAMY2; N. S. BERBISH2
1Associate Prof., Mech. Eng. Dept., Faculty of Engineering, (Shoubra), Zagazig Univ.
2Lecturers, Mech. Eng. Dept., Faculty of Eng., (Shoubra), Zagazig Univ. Cairo, Egypt.
Abstract
This paper provides heat transfer enhancement and flow friction data for swirl flows enter tangentially to an annulus roughened with helical-ribs. The effects of the roughness intensity, tangential to total momentum flux ratio and Reynolds number were studied. The tested annulus has a radius ratio of 0.25 with the inner surface insulated and the outer one was heated with a uniform heat flux. The inner surface of the outer tube was roughened with helically coiled wires which act as turbulence promoters breaking up the viscous sublayer formed in the fluid region nearest to the wall. Roughness was made by using helical-wires at two different diameter to pitch ratios (d/p) of 0.025 and 0.050 within a range of Reynolds number from 5x103 to 25x103, and at values of the tangential to total momentum flux ratios of 1.73, 2.94, 3.46 and 5.88. It was found that there is a significant enhancement in the heat transfer due to inlet injection swirl compared with that gained by helical roughness. Also, the efficiency index is critically dependent on the roughness Reynolds number, momentum flux ratio and the roughness intensity and it is almost less than that for the rough plain annulus. New correlations for Nusselt number enhancement ratio and the Fanning friction factor ratio were obtained as functions of Reynolds number, momentum flux and d/p ratios. Also, a maximum Nusselt number enhancement ratio of about 2.0 was found corresponding to 8.7 fold increase in the flow friction factor for a single entry injector with Mt/MT of 5.88 at relatively dense roughness with d/p of 0.05.
Keywords
Heat transfer augmentation; flow friction; Forced convection; tangential-injected swirl flow; rough annulus; helical ribs
Statistics
Article View: 95
PDF Download: 179