EFFECT OF SOME ENGINEERING PARAMETERS ON THE PERFORMANCE OF A LOCALLY MADE FISH FEED EXTRUDER | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 4, Volume 39, Issue 4, October 2022, Page 537-554 PDF (1.17 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2022.165330.1085 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
Islam F. El-Adly  1; Adel H. Bahnasawy 2; Samir A. Ali 2; El-Sayed G. Khater* 3
| ||||
| 1PhD Stud., Ag. Eng. Dept., Fac. of Ag., Benha U., Egypt. | ||||
| 2Prof. of Ag. Eng., Fac. of Ag., Benha U., Egypt. | ||||
| 3Assoc. Prof. of Ag. Eng., Fac. of Ag., Benha U., Egypt. | ||||
| Abstract | ||||
| Fish feed extruders performance is deeply affected by the operational conditions. Unproper operational condition cause poor quality of feed and affect the productively of such machine, therefore, the main aim of the present work is to study the effect of some engineering parameters (screw speed, feeding rate and die hole diameter) on the performance of a locally made feed extruder. To achieve that, the extruder productivity, total losses percentage, energy consumption and cost per kg of feed were studied at three different screw speeds for main motor of extruder (200, 250 and 300 rpm), three different feeding rates (70, 100 and 130 kgh-1) and three different die hole dimeters were 3, 4 and 5 mm extruder. The results indicated that extruder productivity ranged from 62.24 at 200 rpm , 3mm and 70 kg h-1 to 107.58 kg h-1 at 300 rpm , 5mm and 130 kg h-1 . The highest rate of the losses percentage was 4.64 % which happened at the smallest screw speed (200 rpm), the smallest feeding rate (70 kg h-1) and the largest die hole dimeter (5mm) respectively. The specific energy consumption ranged from 0.126 at 200 rpm , 5mm and 130 kg h-1 to 0.233 kWh kg-1 at 300 rpm , 3mm and 70 kg h-1. The operating cost of fish feed production decreases with the increase of the screw speed, feeding rate and die hole dimeter, the costs of extrusion processing ranged from 0.628 to 1.081 LE kg-1 of feed for all treatments under study. | ||||
| Keywords | ||||
| Productivity; Screw speed; Feed; Die; Cost; Fish feed extruder | ||||
| References | ||||
|
Elleuch, M., Bedigian, D., Roiseux, O., Besbes, S., Blecker, C., and Attia, H. 2010. Dietary fiber and fiber-rich by products of food processing: characterization, technological functionality and commercial applications: A review. Food Chemistry, 124, 411–421.
Fang, Q., Hanna, M.A. and Lan, Y. 2003. Extrusion system design. In: Encyclopedia of Agriculture, Food and Biological Engineering (ed. D.R. Heldman). Marcel Dekker, New York, pp. 306–309.
Fayose, F.T., Ogunlowo, A.S. and Agbetoye, L. 2017. The design, fabrication and preliminary testing of an indigenous single screw extruder. Journal of Engineering Science and Technology, 12(10), 2585-2598.
Kaddour, O.A., Awes, T.R. and Afify, M.K. 2006. Influencing of geometric
dimension of extrusion die holes on machine efficiency and pellets quality. Conference of Mansoura University, Journal of Agricultural Science. 31 (7), 337-359.
Karwe M.V. Kokini J.L. and Ho C. T. 1992. Food Extrusion Science and Technology, 740 pp. New York: Marcel Dekker. Describes advances in extrusion science and technology, ranging from rheology and numerical simulation to flavor and texture generation.
Kurt, G. l979. Engineering formulas. 3rd. Ed. McGraw – Hill book Co.
Metwally, K.A. 2010.Study the effect of some operational Factors on hammer mill. MSc Thesis of Department of Agricultural Engineering, Faculty of Agriculture, Zagazig University. Egypt.
Morad, M.M., Afify, M.K. Kaddour, O.A. and Daood, V. M. 2007. Study on some engineering parameters affecting the performance of fish feed pelleting machine. Misr Journal of Agricultural Engineering, 24(2), 259-282.
Nehu, C. Kurt, A.R. and Muthukmarappan, K. 2005. Utilization of distillers dried grains for fish feed by extrusion technology. A review ASAE Annual International Meeting Sponsored by ASAE. Tampa Convention Center, Tampa, Florida.17-20 July.
Odigboh, E.U. 1997. Machines for crop production. In: Stout BA, editor. Hand book of Agricultural Engineering-Plant Production Engineering. American Society of Agricultural Engineers.
Ojo, S.T., Olukunle, O.J., Aduewa, T.O. and Ukwenya, A.G. 2014. Performance evaluation of floating fish feed extruder. IOSR Journal of Agriculture and Veterinary Science, 7(12), pp.103-113.
Ojomo, A.O., Agbetoye, L.A.S. and Ologunagba, F.O., 2010. Performance evaluation of a fish feed pelletizing machine. ARPN Journal of Engineering and Applied Sciences, 5(9), 88-97. | ||||
|
Statistics Article View: 242 PDF Download: 325 |
||||
