Effect of Providing Semi-Mechanical Carpets with Self-Cleaning Property on Some Physical and Mechanical Properties | ||||
International Design Journal | ||||
Article 9, Volume 13, Issue 1 - Serial Number 50, January and February 2023, Page 109-115 PDF (1.06 MB) | ||||
Document Type: Original Article | ||||
DOI: 10.21608/idj.2023.276067 | ||||
![]() | ||||
Authors | ||||
H. K. Abdel-Tawab1; Aya Ahmed2; Manal Kamal AL Bisi3; Afaf Farag Abd Almotalib4 | ||||
1Spinning & Wearing Dept. Faculty of Applied Arts ,Helwan University | ||||
2Assistant lecturer, Spinning, and Weaving Dept, Faculty of Applied Arts, Helwan University. | ||||
3Professor, Preparations, and Equipment Dept, Textile Division, National Research Center | ||||
4Professor, Spinning and Weaving Dept, Faculty of Applied Arts, Helwan University. Email, Afaffarag1999@yahoo.com | ||||
Abstract | ||||
In Nanotechnology there are two types of self-cleaning surfaces: The first type has a rough microscopic surface that makes dirt particles difficult to adhere it, so thus, pass away easily when washed with water, and the second type depends on the presence of Photoactive layers such as Nano titanium dioxide, which converts air oxygen into active oxygen in the presence of sunlight, as it breaks down organic materials, dirt and stains. Based on the above, it is expected that once the carpet has been treated to give it self-cleaning properties, there will be a change in some physical and mechanical properties of the carpet. This research aims to study the resulting changes in some physical and mechanical properties of carpets produced in a semi-mechanical method after giving it a self-cleaning property and to achieve this goal several samples 27 were produced using the hand-tufted method using different materials, densities pile /cm, and height of the pile. The research methodology depends on the experimental and analytical approach and the link between both, and the study yielded some results, the most important of which are: The best samples that achieved the highest self-cleaning ratio were mixed samples, then polyester samples, and finally wool samples. There is a direct relationship between the density of the pile (the number of stitches of the pile /cm) and the amount of the height of the pile (mm) and the percentage of loss in the thickness under the influence of a static load of the samples produced under research (when the textile specifications used are stable). Increasing the percentage of the loss in the thickness under the influence of a static load for carpet samples produced under research after the treatment than before the treatment. There is a direct relationship between the pile density (the number of stitches of the pile /cm) the amount of the pile height (mm) and the percentage of the carpet's resistance to abrasion by friction for the carpet samples produced under research (when the textile specifications used are stable). Increasing the percentage of the friction resistance of the carpet samples produced under research after the treatment than before the treatment. | ||||
Keywords | ||||
Semi; Mechanical Carpet — Nanotechnology — Self Cleaning — Nanotitanium Dioxide | ||||
Supplementary Files
|
||||
References | ||||
1- Nielsen, N., Nanotechnology and Its Impact on Consumers, Report to the Consumer Council of Canada, EBN Consulting, 2008.
2- Federal Environment Agency (Umweltbundesamt), Fact Sheet Nano Products (Use of Nanomaterial in Textiles), April 19, 2013.
3- Y.W.H. Wong, C.W.M. Yuen1, M.Y.S. Leung, S.K.A. Ku1, and H.L.I. Lam Selected Applications Of Nanotechnology In Textiles, AUTEX Research Journal, Vol. 6, No. 1, March 2006.
4- Subrata Chandra Das1, Debasree Paul1, Sk. Md. Mahamudul Hassan, Application of Nanotechnology in Textiles: A Review, Chittagong, Bangladesh, May 2014.
5- Lauterwasser, C., Opportunities and risks of Nanotechnologies, The Allianz Center for Technology and Allianz Global Risks, France, 2014.
6- J. K. PATRA, and S. GOUDA, Application of nanotechnology in textile engineering: An overview, J. Eng. Technol. Res. May 2013.
7- Ola Abdel-Salam Barakat Mohamed, “Opportunities and risks of nanotechnology and the changes it causes in some of the main properties related to the feeling of comfort in cellulosic materials.” - Journal of Architecture and Arts - Eleventh Issue - Part One - 2020 AD.
8- American Association for Testing and Materials – “Annual Book of ASTM” – Vol, 07, 01 -1994.
9- The Egyptian Standard Specification 2440- 1993.
10- The Egyptian Standard Specification 2581- 1993.
11- American Association for Testing and Materials – “Annual Book of ASTM” – Vol, 07, 02 -1994. | ||||
Statistics Article View: 178 PDF Download: 262 |
||||