Alginic/Stearic/Octadecane as Phase Change Material (PCM) for enhancing the thermal Comfort-ability of Different Polyester Fabrics Constructions
Fathallah, A., Youssef, B., El-Sadek, H., Amin, M., Abd El-Kader, B., El-Kambashawy, Y., Halawa, O., Hassabo, A. (2023). Alginic/Stearic/Octadecane as Phase Change Material (PCM) for enhancing the thermal Comfort-ability of Different Polyester Fabrics Constructions. EKB Journal Management System, 66(4), 167-177. doi: 10.21608/ejchem.2023.188010.7468
Abeer I. Fathallah; Bassant Y. Youssef; Habiba El-Sadek; Menaa G. Amin; Basma M. Abd El-Kader; Youssef M. El-Kambashawy; Osama E. Halawa; Ahmed G. Hassabo. "Alginic/Stearic/Octadecane as Phase Change Material (PCM) for enhancing the thermal Comfort-ability of Different Polyester Fabrics Constructions". EKB Journal Management System, 66, 4, 2023, 167-177. doi: 10.21608/ejchem.2023.188010.7468
Fathallah, A., Youssef, B., El-Sadek, H., Amin, M., Abd El-Kader, B., El-Kambashawy, Y., Halawa, O., Hassabo, A. (2023). 'Alginic/Stearic/Octadecane as Phase Change Material (PCM) for enhancing the thermal Comfort-ability of Different Polyester Fabrics Constructions', EKB Journal Management System, 66(4), pp. 167-177. doi: 10.21608/ejchem.2023.188010.7468
Fathallah, A., Youssef, B., El-Sadek, H., Amin, M., Abd El-Kader, B., El-Kambashawy, Y., Halawa, O., Hassabo, A. Alginic/Stearic/Octadecane as Phase Change Material (PCM) for enhancing the thermal Comfort-ability of Different Polyester Fabrics Constructions. EKB Journal Management System, 2023; 66(4): 167-177. doi: 10.21608/ejchem.2023.188010.7468

Alginic/Stearic/Octadecane as Phase Change Material (PCM) for enhancing the thermal Comfort-ability of Different Polyester Fabrics Constructions

Egyptian Journal of Chemistry
Volume 66, Issue 4, April 2023, Page 167-177  XML PDF (405.37 K)
Document Type: Original Article
DOI: 10.21608/ejchem.2023.188010.7468
View on SCiNiTO View on SCiNiTO
Authors
Abeer I. Fathallah1; Bassant Y. Youssef1; Habiba El-Sadek1; Menaa G. Amin1; Basma M. Abd El-Kader1; Youssef M. El-Kambashawy1; Osama E. Halawa2; Ahmed G. Hassabo email orcid 3
1Textile Printing, Dyeing and Finishing Department, Faculty of Applied Arts, Helwan University, Cairo, Egypt
2Spinning, Weaving and Knitting Department, Faculty of Applied Arts, Helwan University, Cairo, Egypt
3National Research Centre (NRC), Textile Research and Technology Institute (TRTI), Pre-treatment and Finishing of Cellulose-based Textiles Department (PFCTD), El-Behouth St. (former El-Tahrir str.), Dokki, P.O. 12622, Giza, Egypt
Abstract
One of the most extensively used textile materials is polyester, which comes in a variety of textile, yarn, and fiber forms. This is dependent on the characteristics of the polyester polymer and its intended usage of it. To give different polyester fabrics, the ability to change their thermal state over a wide range and be used for thermal protection for a variety of purposes, regardless of ambient temperatures, this research aims to improve the thermal heat profiles for those fabrics when constructed with Phase Change Material (PCM). To create PCM composite treatment materials, various polyester fabric constructions were simply treated utilizing Octadecane as (PCM material) loaded on alginic/stearic acid. Following treatment with the KES thermal conductivity system and Differential Scanning Calorimetry (DSC), the textiles' qualities were assessed, and their physicomechanical properties were also looked at. Conclusion: Polyester textiles can be coated with PCM composites, and the covered version performs better than the uncovered version. Additionally, it was found that these treatments improved the mechanical and physical qualities but had no effect on the permeability to air and water vapor following examination of the attributes of blank/uncovered and covered polyester textiles.
Keywords
Polyester; Octadecane; Phase Change Material (PCM); Thermal profile
Statistics
Article View: 269
PDF Download: 206