MODELING & DESIGNING OF A SOLAR FURNACE FOR CURING GEOPOLYMER BRICKS | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 8, Volume 40, Issue 3, July 2023, Page 259-278 PDF (2.23 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2023.211436.1100 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
M. A. Mahmoud1; M. H. Ibrahim2; M. I. N. Morsy3; A. ِA. Ali  4
| ||||
| 1Grad. Stud., Ag. and Bio. Eng., Fac. of Ag., EL-Shatby, Alex. U., Egypt. | ||||
| 2Prof., Dr. of Bio-Environmental Sys. Eng. & Energy, Ag. and Bio. Eng., Fac. of Ag., EL-Shatby, Alex. U., Egypt. | ||||
| 3Assoc. Prof., Dr. of Bio-Environmental Sys. Eng., Ag. and Bio. Eng., Fac. of Ag., EL-Shatby, Alex. U., Egypt. | ||||
| 4Assist. Prof., Dr. of irrigation Sys., Ag. and Bio. Eng., Fac. of Ag., EL-Shatby, Alex. U., Egypt. | ||||
| Abstract | ||||
| This research was devoted to design an unfired brick solar furnace, heated and powered using solar energy. Mathematical model was developed to predict the configuration and performance of a system consisting of several components to produce geopolymer bricks. A computer program by using JavaScript consisting of a main routing and three subroutines was developed. The sizes of the solar collector and of solar panel are the performance of the interior heat exchangers. The temperature of the bricks was predicted. Error analysis techniques are used to validate the predicted results versus the measured values. The predicted results show good agreement with the measured values (R² = 0.9823). Also, the output results indicated directly the heating load required inside the solar furnace to dry the unfired brick with a designed interior air temperature at 100˚C range between maximum heating load required "916.72 Watt" at midnight and the minimum value "810 Watt" at near noon. Output results of the computer models were used afterwards for design and construct the solar furnace system for curing unfired bricks. | ||||
| Keywords | ||||
| Renewable energy; Computer models; Solar furnace; Friendly bricks | ||||
| References | ||||
|
ASHRAE (2001)– American Society of Heating, Refrigerating and Air Conditioning Engineers. ASHRAE Handbook – Fundamentals. Atlanta, SI ed.
Bhat, M. S., Afeefa, Q. S., Ashok, K. P., & Bashir, A. G. (2014). Brick kiln emissions and its environmental impact: A Review. Journal of Ecology and the Natural Environment, 6(1), 1-11.
Chang, C. T., Hong, G. B., & Lin, H. S. (2016). Artificial lightweight aggregate from different waste materials. Environmental Engineering Science, 33(4), 283-289.
Holman, J.P. (1981) Heat Transfer (International Student Edition). McGraw Hill International Book Co.
Jamal, J., Tangkemanda, A., & Susanto, T. A. (2018, June). The effect of collector slope angle on the performance of solar water heater. In AIP Conference Proceedings (Vol. 1977, No. 1, p. 060019). AIP Publishing LLC.
Kayali, O., Khan, M. S. H., & Ahmed, M. S. (2012). The role of hydrotalcite in chloride binding and corrosion protection in concretes with ground granulated blast furnace slag. Cement and Concrete Composites, 34(8), 936-945.
Legates, D. R., & McCabe Jr, G. J. (1999). Evaluating the use of “goodness‐of‐fit” measures in hydrologic and hydroclimatic model validation. Water resources research, 35(1), 233-241.
Loague, K., & Green, R. E. (1991). Statistical and graphical methods for evaluating solute transport models: overview and application. Journal of contaminant hydrology, 7(1-2), 51-73.
Shakir, A. A., & Mohammed, A. A. (2013). Manufacturing of Bricks in the Past, in the Present and in the Future: A state of the Art Review. International Journal of Advances in Applied Sciences (IJAAS), 2(3), 145-156.
Shawabkeh, R. (2015). Steps for design of Heat Exchanger. King Fahd University of Petroleum & Minerals.
Sudharsan, N., & Palanisamy, T. (2018). A comprehensive study on potential use of waste materials in brick for sustainable development. Ecology, Environment and Conservation, 24(September), S339-S343.
Turner, L. K., & Collins, F. G. (2013). Carbon dioxide equivalent (CO2-e) emissions: A comparison between geopolymer and OPC cement concrete. Construction and building materials, 43, 125-130. Willmott, C. J., Ackleson, S. G., Davis, R. E., Feddema, J. J., Klink, K. M., Legates, D. R., & Rowe, C. M. (1985). Statistics for the evaluation and comparison of models. Journal of Geophysical Research: Oceans, 90(C5), 8995-9005. | ||||
|
Statistics Article View: 210 PDF Download: 118 |
||||
