Achieving Optimum Comfort Properties of Multilayered Hospital Bed Sheet Fabrics | ||||
| International Design Journal | ||||
| Article 26, Volume 14, Issue 5 - Serial Number 63, September and October 2024, Page 349-357 PDF (2.01 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/idj.2024.372790 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| Hafez S. Hawas1; Alaa Abdulhamid Ali2; Heba Abdulaziz Shalaby3 | ||||
| 1Lecturer at Spinning, Weaving & Knitting dept., Faculty of Applied Arts, Helwan University, Egypt | ||||
| 2Demonstrator, Spinning, Weaving and Knitting Dep, Faculty of Applied Arts, Benha | ||||
| 3Professor and Head of Spinning, Weaving and Knitting Dep - Faculty of Applied Arts - Benha University | ||||
| Abstract | ||||
| Hospital bed sheets are one of the most important health care products that must provide patient comfort properties such as absorbency, breathability, moisture management properties, and resistance to the growth of bacteria and fungi. A lot of damage occurs when bed sheets are unable to transfer body heat and the secretions resulting from it, which leads to the creation of a moisture-laden atmosphere beneath the patient, which helps increase body temperature and the growth of microorganisms, and this is one of the most important causes of bed sores. The commercially available hospital bed sheets made of fibers such like cotton, polyester and their blends which are not sufficient Due to this, the research tended to produce medical bed sheeting fabrics using a multi-layered method to achieve the property of moisture management, as well as the use of new fibers such as (bamboo, polyester microfiber) as well as the use of cotton also to provide physiological comfort for the patient, as bamboo material was used in the face layer, polyester microfiber in inner layer and cotton in the back layer to transmit the body heat and fluids, which makes the patient not feel comfortable. The research relied on the production of 6 samples using a multi-layered method and 2 variables, first: 2 different weft arrangement (1 face: 1 back: 1filling) and (1 face: 1 back: 2 filling), second: the use of three weave structures for the face layer (hanycomb8, twill1/3, satin4) and the use of fixed weave structure in all samples for the back layer (basket2/2) The cohesion between the layers was achieved by cohesion from the warp. Laboratory tests were carried out on these samples and statistical analysis was carried out. Research problem: The need for bed sheets that work to transfer moisture resulting from the patient’s secretions to the external environment (moisture management system) to reduce the occurrence of bed sores. The lack of scientific studies that study the effect of using the double method and the proportions of fillers on the fabrics of medical bed sheets. Research aims: Production of bed sheet fabrics using multi-layer method to reduce the formation of bedsores. Take advantage of the various materials in the layers to achieve a moisture management system in bed sheets. Research importance: Improving the functional properties of hospital bed sheet fabrics using multi-layer method and various materials to reduce bed sores. Contribute to the provision of a specialized scientific and academic study that studies the fabrics of multi-layered hospital bed sheets to resist bed sores. Research Hypothesis: The use of multi-layer method with different filler ratios affects the achievement of the research objective. The use of different structures of statistical significance in achieving the objective of the research. Research Methodology: this research follows the analytical and experimental method | ||||
| Keywords | ||||
| Technical Textile; Medical textile; Moisture Management; Bed Sores | ||||
|
Supplementary Files
|
||||
| References | ||||
|
1- Sherif, Fawzi Saeed Zaki & El-Sayed, Noha Mohamed Abdo (2017) "A descriptive study of medical textiles and a proposed vision for how to benefit from them in opening new markets in the Egyptian textile industry" Journal of Specific Education Research - Mansoura University, Issue (46)
2- Abdel Wahab, Hanan Mustafa (1997) "Production of fabrics with special specifications to resist the occurrence of bed ulcers" Master Thesis, Faculty of Applied Arts: Helwan University,
3- Ola Abdel Salam, Nassar, E.M.Abou-taleb) 2017( “Effect of bed sheet fabric construction on the reduction of bed sores” International journal of advance research in science and engineering vol 6,issue 8 .
4- Mabrouk, Heba Khamis Abdel Tawab (2013) "Achieving the best functional properties of the production of airbag fabrics in cars" PhD thesis, Faculty of Applied Arts: Helwan University.
5- Udyog Bhavan, )2004(“REPORT OF THE EXPERT COMMITTEE ON TECHNICAL TEXTILES”, vol.1, Government of India Ministry of Textiles.
6- Byrne, C.,) 2000(“technical textiles market- an overview “in handbook of technical textiles, Horrocks, A.R., and Annad S. C., Eds, Cambridge UK: Woodhead Publishing Limited.
8- Abdullah, Marwa Atef Ali (2001) "Achieving the best standards for the production of diapers to suit their job performance", Master Thesis, Faculty of Applied Arts: Helwan University.
9- A.A. Dawoud. )2016( “Effect of microfiber polyester woven fabrics, international journal of engineering sciences vol 3, no 11,
10- Sundaresan, S., Ramesh, M., Sabitha, V., Ramesh, M., &Ramesh, V.)2016(“A detailed analysis on physical and comfort properties of bed linen woven fabrics”., international journal of advance research and innovation ideas in Education, vol.2
11- S. K. Chinta, Ms. Pooja D. Gujar )2013(“Significance of moisture management for high performance textile fabrics “international journal of innovative research in science, engineering, and technology Vol.2.
12- M.Manshahia &A Das. )2014( “High active sportswear – A critical review”, Indian journal of fiber & textile research vol 39.
13- N. Niles, S. Fernando )2021(“Two-layer fabrics for moisture management” Research Journal of Textile and Apparel Vol. 25 No. 1.
14- (NPUAP/EPUAP) 2009: European pressure Ulcer Advisory Panel &Nation Pressure Ulcer Advisory Panel: Treatment of pressure Ulcers,
15- Debashish Nayak. K. Srinivasan )2008(” Bedsores: “top to bottom” and “bottom to top” Indian Journal of Surgery ·
17- Kandha V Adivu P )2011(“Design and development of hospital textiles using lyocell fiber and its blend.” Faculty of technology anna university chennal.
18- Joseph E Grey, Stuart Enoch, Keith G Harding )2006(“Pressure ulcers” BMJ Clinical Research · VOL 332.
19- P. Kandha Vadivu) 2013(” Design and Development of Portable Support Surface and Multilayered Fabric Cover for Bed Sore Prevention” Association of Surgeons of India.
20- ASTM D737 – 04 (2012) “Standard test method for air permeability of textile fabrics”
21- BS 7209 - Specification for water vapour permeable apparel fabrics
22- AATC TM79, 2000” Standard Test method for absorbency of textiles”
AATC 198-2012 (R2013), “Standard test method for horizontal wicking of textile | ||||
|
Statistics Article View: 208 PDF Download: 155 |
||||
