EFFECT OF SIZE AND SHAPE OF ELECTRODES ON THE PERFORMANCE OF EDM
A., K., M., H., A, Y. (2008). EFFECT OF SIZE AND SHAPE OF ELECTRODES ON THE PERFORMANCE OF EDM. EKB Journal Management System, 13(13th International Conference on Applied Mechanics and Mechanical Engineering.), 17-25. doi: 10.21608/amme.2008.39059
KHAN A. A.; HAQUE M. M.; YEAKUB M. A. "EFFECT OF SIZE AND SHAPE OF ELECTRODES ON THE PERFORMANCE OF EDM". EKB Journal Management System, 13, 13th International Conference on Applied Mechanics and Mechanical Engineering., 2008, 17-25. doi: 10.21608/amme.2008.39059
A., K., M., H., A, Y. (2008). 'EFFECT OF SIZE AND SHAPE OF ELECTRODES ON THE PERFORMANCE OF EDM', EKB Journal Management System, 13(13th International Conference on Applied Mechanics and Mechanical Engineering.), pp. 17-25. doi: 10.21608/amme.2008.39059
A., K., M., H., A, Y. EFFECT OF SIZE AND SHAPE OF ELECTRODES ON THE PERFORMANCE OF EDM. EKB Journal Management System, 2008; 13(13th International Conference on Applied Mechanics and Mechanical Engineering.): 17-25. doi: 10.21608/amme.2008.39059

EFFECT OF SIZE AND SHAPE OF ELECTRODES ON THE PERFORMANCE OF EDM

The International Conference on Applied Mechanics and Mechanical Engineering
Article 30, Volume 13, 13th International Conference on Applied Mechanics and Mechanical Engineering., May 2008, Page 17-25  XML PDF (820.48 K)
Document Type: Original Article
DOI: 10.21608/amme.2008.39059
View on SCiNiTO View on SCiNiTO
Authors
KHAN A. A.1; HAQUE M. M.1; YEAKUB M. A2
1Professor, Dept. of Manufacturing and Materials Engineering IIUM, Malaysia.
2Associate professor, Dept. of Manufacturing and Materials Engineering IIUM, Malaysia.
Abstract
ABSTRACT
In the present study the effect of size and different shapes of electrodes on material
removal rate (MRR), job surface finish and wear ratio (WR) during EDM has been
investigated. The work material taken was mild steel and the electrode material taken
was copper. The size of the electrodes was 9mm, 15 mm, 20 mm and 30 mm in
diameter. The shapes of the electrodes were square, round, triangular and diamond,
having the same area of cross-section. The highest MRR was found for round
electrodes followed by square, triangular and diamond shaped electrodes. MRR was
found to increases sharply with the increase in diameter of the electrodes. With
increase in current, the sparks produced are of higher thermal energy. As a result,
increase in current resulted increase in MRR. A higher thermal energy also erodes
more material from the electrode. Electrode wear (EW) was measured along the crosssection
of the electrode as well as along its length. EW was also found to increase with
the increase in current. However, the highest EW was fond on the diamond shaped
electrodes followed by triangular, square and the round shaped ones. An electrode of
smaller cross-section exhibited a higher electrode wear. Wear ratio (WR) was
calculated as the ratio of the volume of material removed from the electrode to the
same removed from the work material. The highest WR was found on the diamond
shaped electrodes followed by triangular, square and round electrodes. It was also
found that WR decreases with increase in cross-sectional area of the electrode. Job
surface roughness was found to decrease with increase in electrode diameter, but the
effect is very insignificant. The smoothest job surface finish was found for round
electrodes followed by square, triangular and diamond shaped electrodes. But again,
the influence of the shape of the electrodes on job surface finish was found to be
insignificant.
Keywords
EDM; Material Removal Rate; Electrode wear; Size and shape of electrodes; Surface roughness
Statistics
Article View: 91
PDF Download: 96