Kinematic Modeling, Dexterity and Performance Analysis of Planar Parallel Manipulators | ||||
| Menoufia Journal of Electronic Engineering Research | ||||
| Article 5, Volume 27, Issue 2, July 2018, Page 105-140 | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjeer.2018.63183 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| Amr Abo Salem; Tarek Y. Khedr; Gamal El Ghazaly; M. I. Mahmoud | ||||
| Department of Industrial Electronics and Control Engineering, Faculty of Electronic Engineering at Menouf, Menofia University, Egypt | ||||
| Abstract | ||||
| This research work is concerned with the Planar Parallel Manipulator (PPM). This investigation leads to a comparative study between the 2-RRR PPM which is a non-redundant PPM and 3-RRR PPM which is a redundant PPM. The main objective is to compare one type of PPM with another one that has one step of construction’s upgrading with respect to the other PPM. An important issue for optimal design of these manipulators is related to their performance characterizations. These two PPMs are introduced with their mechanism construction. Investigation of characteristics of PPMs goes through the complexity of the direct and inverse kinematics problems, which are solved using the suggested and proper geometrical equations. The dexterous workspace is geometrically obtained where the End-Effector (EE) can reach and illustrate some of its properties. In order to complete the study for these PPMs, the virtual work is determined, obtained and used, to get the PPM characteristics using the dynamic model. Jacobian matrix has been determined and used. This research work is terminated not only by two kinematic characteristics maps dexterity and manipulability - indices, but also with a dynamic characteristics map called dynamic index. | ||||
| Keywords | ||||
| Planar Parallel Manipulator (PPM); End-Effector (EE); Redundancy; Kinematic Model; Degree of Freedom (DOF); Performance indices | ||||
| References | ||||
|
[1] Y. D. Patel, P. M. George: Parallel Manipulators ApplicationsA Survey, http://dx.doi.org/10.4236/mme.2012.23008. [2] Merlet, Jean-Pierre. Parallel robots. Vol. 128. Springer Science and Business Media, 2006. [3] Carretero, Juan A., Iman Ebrahimi, and Roger Boudreau. "Overall Motion Planning for Kinematically Redundant Parallel Manipulators." Journal of Mechanisms and Robotics 4.2 (2012): 024502. [4] Park, F. C., and Jin Wook Kim. "Singularity analysis of closed kinematic chains." TRANSACTIONS-AMERICAN SOCIETY OF MECHANICAL ENGINEERS JOURNAL OF MECHANICAL DESIGN 121 (1999): 32- 38. [5] Kock, Snke, and Walter Schumacher. "A parallel xy manipulator with actuation redundancy for high-speed and active-stiffness applications." Robotics and Automation, 1998. Proceedings. 1998 IEEE International Conference on. Vol. 3. IEEE, 1998. [6] Gosselin, Clment M., and Jean-Pierre Merlet. "The direct kinematics of planar parallel manipulators: special architectures and number of solutions." Mechanism and Machine Theory 29.8 (1994): 1083-1097. [7] Gao, Feng, Xinjun Liu, and William A. Gruver. "Performance evaluation of twodegree-of freedom planar parallel robots." Mechanism and Machine Theory 33.6 (1998): 661-668. [8] Shin, Hyunpyo, et al. "Kinematic optimization of a redundantly actuated parallel mechanism for maximizing stiffness and workspace using Taguchi method." Journal of Computational and Nonlinear Dynamics 6.1 (2011): 011017. [9] Ebrahimi, Iman, Juan A. Carretero, and Roger Boudreau. "3-PRRR redundant planar parallel manipulator: Inverse displacement, workspace and singularity analyses." Mechanism and Machine Theory 42.8 (2007): 1007-1016. [10] Garg, Venus, Scott B. Nokleby, and Juan A. Carretero. "Wrench capability analysis of redundantly actuated spatial parallel manipulators." Mechanism and machine theory 44.5 (2009): 1070-1081. [11] Wu, Jun, et al. "Stiffness and natural frequency of a 3-DOF parallel manipulator with consideration of additional leg candidates." Robotics and Autonomous Systems 61.8 (2013): 868-875. [12] Hrones, John Anthony, and George Larsen Nelson. Analysis of the fourbar linkage: its application to the synthesis of mechanisms. Published jointly by the Technology Press of the Massachusetts Institute of Technology, and Wiley, New York, 1951. [13] Modeling, performance analysis and control of robot manipulators/edited by Etienne Dombre, Wisama Khalil. p. cm. Includes index. ISBN-13: 978- 1-905209-10-1 ISBN-10: 1-905209-10-X 1. Robotics. 2. Manipulators (Mechanism) I. Dombre, E. (Etienne) II. Khalil, W. (Wisama) TJ211.M626 2006 629.8’933-dc22 [14] A. K. Dash, I. M. Chen, S. H. Yeo, G. Yang: Task-oriented configuration design for reconfigurable parallel manipulator systems, International Journal of Computer Integrated Manufacturing, Vol. 18, No. 7, pp. 615- 634, 2005. [15] L. W. Tsai, Robot Analysis: The Mechanics of Serial and Parallel Manipulators, USA: John Wiley and Sons, 1999. [16] Zoran PANDILOV,Vladimir DUKOVSKI: Comparison of The Characteristics Between Serial and Parallel Robots, ISSN: 2067 3809. [17] Balan R., V. Maties, S. Stan, C. Lapusan: On the Control of a 3-RRR Planar Parallel Minirobot, Journal Mecatronica, Journal of Romanian Society of Mechatronics, no. 4/2005 , pp. 20-23, December, 2005. [18] A. A. Maciejewski and C. A. Klein: Obstacle avoidance for kinematically redundant manipulators in dynamically varying environments, Int. J. Robot. Res. 4(3), 109117 (1985). [19] Y. Nakamura, H. Hanafusa and T. Yoshikawa: Task-priority based redundancy control of robot manipulators, Int. J. Robot. Res. 6(2), 315 (1987). [20] J. Wang and C. M. Gosselin: Kinematic analysis and design of kinematically redundant parallel mechanisms.J. Mech. Des. 126(1), 109118 (2004). [21] V. Garg, S. B. Nokleby and J. A. Carretero: Determining the Force and Moment Workspaces of Redundantly-Actuated Spatial Parallel Manipulators. Proceedings of the 2007 ASME DETC, Las Vegas, Nevada, USA. [22] Weiwei Shang, Shuang Cong.: Dexterity and Adaptive Control of Planar Parallel Manipulators With and Without Redundant Actuation. Contributed by the Design Engineering Division of ASME for publication in Journal of Computational and Nonlinear Dynamics. [23] http://www.mecademic.com/DexTAR.html, signed in 2/2017. [24] T. Yoshikawa: Manipulability of robotic mechanisms, The International Journal of Robotics Research, vol. 4, no. 2, pp. 39, 1985. [25] Pu Zhang, Zhenqiang Yao, Zhengchun Du.: Global Performance Index System for Kinematic Optimization of Robotic Mechanism. Contributed by the Mechanisms and Robotics Committee of ASME for publication in the Journal of Mechanical Design. [26] Gosselin, Clement, and Jorge Angeles. "Singularity analysis of closed-loop kinematic chains." IEEE transactions on robotics and automation 6.3 (1990): 281-290. [27] Sefrioui, Jaouad, and Clment M. Gosselin. "Singularity analysis and representation of planar parallel manipulators." Robotics and Autonomous Systems 10.4 (1992): 209-224. [28] Hubert, J., and J-P. Merlet. "Static of parallel manipulators and closeness to singularity." Journal of Mechanisms and Robotics 1.1 (2009): 011011. [29] Rubbert, Lennart, et al. "Using singularities of parallel manipulators to enhance the rigid-body replacement design method of compliant mechanisms." Journal of Mechanical Design 136.5 (2014): 051010. [30] Liu, Guanfeng, Yunjiang Lou, and Zexiang Li. "Singularities of parallel manipulators: A geometric treatment." IEEE Transactions on Robotics and Automation 19.4 (2003): 579-594. [31] Tsai, Lung-Wen. Robot analysis: the mechanics of serial and parallel manipulators. John Wiley, Sons, 1999. [32] Briot, Sbastien, and Vigen Arakelian. "Optimal force generation in parallel manipulators for passing through the singular positions." The International Journal of Robotics Research 27.8 (2008): 967-983. [33] He, J. F., et al. "A survey on control of parallel manipulator." Key Engineering Materials. Vol. 339. Trans Tech Publications, 2007. [34] Nakamura, Yoshihiko, and Hideo Hanafusa. "Inverse kinematic solutions with singularity robustness for robot manipulator control." ASME, Transactions, Journal of Dynamic Systems, Measurement, and Control 108 (1986): 163-171. [35] Tan, Jindong, and Ning Xi. "Hybrid system design for singularityless task level robot controllers." Robotics and Automation, 2000. Proceedings. ICRA’00. IEEE International Conference on. Vol. 3. IEEE, 2000. [36] Mohamed, Maher G., and Clment M. Gosselin. "Design and analysis of kinematically redundant parallel manipulators with configurable platforms." IEEE Transactions on Robotics 21.3 (2005): 277-287. [37] Dasgupta, Bhaskar, and T. S. Mruthyunjaya. "Force redundancy in parallel manipulators: theoretical and practical issues." Mechanism and Machine Theory 33.6 (1998): 727-742. [38] Cheng, Hui, et al. "Advantages and dynamics of parallel manipulators with redundant actuation." Intelligent Robots and Systems, 2001. Proceedings. 2001 IEEE/RSJ International Conference on. Vol. 1. IEEE, 2001. [39] Slotine, Siciliano B. "A general framework for managing multiple tasks in highly redundant robotic systems." proceeding of 5th International Conference on Advanced Robotics. Vol. 2. 1991. [40] Park, Frank C., and Jin Wook Kim. "Manipulability and singularity analysis of multiple robot systems: A geometric approach." Robotics and Automation, 1998. Proceedings. 1998 IEEE International Conference on. Vol. 2. IEEE, 1998. [41] Quennouelle, Cyril, and C. M. Gosselin. "Stiffness matrix of compliant parallel mechanisms." Advances in Robot Kinematics: Analysis and Design (2008): 331-341. [42] Alici, Grsel, and Bijan Shirinzadeh. "Enhanced stiffness modeling, identification and characterization for robot manipulators." IEEE transactions on robotics 21.4 (2005): 554-564. [43] Baruh, Haim. Analytical dynamics. Boston: WCB/McGraw-Hill, 1999. | ||||
|
Statistics Article View: 371 |
||||
