Effect of laminate veneer designs on abfraction incidence using different loading conditions “finite element analysis”
El Badawy, A., Abd El Aziz, M., Omar, E. (2019). Effect of laminate veneer designs on abfraction incidence using different loading conditions “finite element analysis”. EKB Journal Management System, 65(Issue 2 - April (Fixed Prosthodontics, Dental Materials, Conservative Dentistry & Endodontics)), 1645-1652. doi: 10.21608/edj.2019.72635
Adel A. El Badawy; Mohammed H. Abd El Aziz; Elsayed A. Omar. "Effect of laminate veneer designs on abfraction incidence using different loading conditions “finite element analysis”". EKB Journal Management System, 65, Issue 2 - April (Fixed Prosthodontics, Dental Materials, Conservative Dentistry & Endodontics), 2019, 1645-1652. doi: 10.21608/edj.2019.72635
El Badawy, A., Abd El Aziz, M., Omar, E. (2019). 'Effect of laminate veneer designs on abfraction incidence using different loading conditions “finite element analysis”', EKB Journal Management System, 65(Issue 2 - April (Fixed Prosthodontics, Dental Materials, Conservative Dentistry & Endodontics)), pp. 1645-1652. doi: 10.21608/edj.2019.72635
El Badawy, A., Abd El Aziz, M., Omar, E. Effect of laminate veneer designs on abfraction incidence using different loading conditions “finite element analysis”. EKB Journal Management System, 2019; 65(Issue 2 - April (Fixed Prosthodontics, Dental Materials, Conservative Dentistry & Endodontics)): 1645-1652. doi: 10.21608/edj.2019.72635

Effect of laminate veneer designs on abfraction incidence using different loading conditions “finite element analysis”

Egyptian Dental Journal
Article 25, Volume 65, Issue 2 - April (Fixed Prosthodontics, Dental Materials, Conservative Dentistry & Endodontics), April 2019, Page 1645-1652  XML PDF (1.37 MB)
Document Type: Original Article
DOI: 10.21608/edj.2019.72635
View on SCiNiTO View on SCiNiTO
Authors
Adel A. El Badawy; Mohammed H. Abd El Aziz; Elsayed A. Omar
Assistant professor, Crown and Bridge Department, Faculty of Dentistry, Al Azhar University
Abstract
Statement of problem: Abfraction incidence is usually challenging and difficult to be identified accurately, especially, in case of existing restoration.
Aim of the study: This study aimed to evaluate the influence of laminate veneer design on abfraction incidence in maxillary central incisor with different loading protocols using finite element analysis.
Materials and methods: Maxillary central incisor was subjected to Computerized tomography (CT) scan to obtain 3D finite element model. Tooth without restoration (control) was subjected to a load of 100 N at 60° and 125°, the same load was applied with the previous directions on the tooth model with lithium disilicate laminate veneer using three preparation designs: veneer is taken up to the incisal edge level but the edge, is not reduced (Feather) (FP), design (FP) is prepared with 0.5mm incisal reduction without palatal overlapping (Butt joint.) (BJP) and (POP) in which, design (FP) is prepared with 2 mm incisal reduction and 0.5 mm palatal overlap.
Results: In feather preparation (FP) design, stress values were slightly higher than that in control model in enamel and dentin at both load directions. While, but joint preparation (BJP) design exhibited the lowest stress in both layers and direction of load.
Conclusion Highest stresses were concentrated at the cement – enamel junction in all loading scenarios, butt joint preparation (BJP) design in both load conditions developed lower stresses than that in other designs, and feather preparation (FP) design suggested the probability of abfraction formation.
Statistics
Article View: 237
PDF Download: 368