The Effect of Precipitation Hardening on the Properties Hadfield Steel | ||||
| ERJ. Engineering Research Journal | ||||
| Article 4, Volume 43, Issue 2, April 2020, Page 119-125 PDF (837.8 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/erjm.2020.83899 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| Amr A. Mohamed1; M. K. El-fawkhry2; W. M. El-nahas3 | ||||
| 1Faculty of Industrial Education, Helwan University, Egypt | ||||
| 2Central Metallurgical Research and Development Institute (CMRDI), Egypt. | ||||
| 3Faculty of Industrial Education, Helwan University, Egypt. | ||||
| Abstract | ||||
| The precipitation hardening in chromium containing Hadfield steel is considered as the most traditional mechanism for promoting the technological and mechanical properties of such high alloy steel. Two methodologies of precipitation hardening were suggested to attain the strengthening mechanical and technical properties of this steel. Different precipitates of chromium carbides were stimulated through either pre and post solution hardening treatment. Thereby, the results of the two mechanisms were compared in terms of precipitation morphology, compositions, and mechanical properties. It was found that the deteriorative of toughness was significantly observed at the post solution treatment. Fine chromium carbides Cr7C3, and Cr23C6 were observed throughout the austenite matrix at 650oC, and 700oC as the temperature of the pre-solution treatment technique. It was found that the morphology of chromium carbides has the most significant effect on promoting the strain-hardening property of Hadfield steel studied. When conducting the age-hardening regime followed the solution treatment observed the best toughness of Hadfield steel. | ||||
| Keywords | ||||
| precipitation hardening; Hadfield steel; morphology | ||||
| References | ||||
|
[1] KHAN, Abdul Faheem, et al.Microstructural changes in Hadfield steel. Pakistan journal of applied sciences, 1.3: 317-320,( 2001). [2] QIAN, Lihe; FENG, Xiaoyong; ZHANG, Fucheng. Deformed microstructure and hardness of Hadfield high manganese steel. Materials transactions, 52.8: 1623-1628, (2011). [3] TĘCZA, G.; SOBULA, S. Effect of heat treatment on change microstructure of cast high-manganese hadfield steel with elevated chromium content. Archives of Foundry Engineering, 14, (2014).
[4] PRIBULOVA, Alena; BABIC, Jozef; BARICOVA, Dana. Influence of hadfield’s steel chemical composition on its mechanical properties. Chem. Listy, 105: 430-432, (2011). [5] SRIVASTAVA, Ashok Kumar; DAS, Karabi. Microstructural characterization of Hadfield austenitic manganese steel. Journal of Materials Science, 43.16: 5654-5658, (2008). [6] ZHENG, Chengsi, et al. Tailoring mechanical behavior of a fine-grained metastable austenitic stainless steel by pre-straining. Materials Science and Engineering: A, 746: 332-340, (2019). [7] HOSSEINI, Shabnam; LIMOOEI, Mohammad Bagher. Optimization of heat treatment to obtain desired mechanical properties of high carbon Hadfield steels. World applied sciences journal, 15.10: 1421-1424, (2011). [8] XIONG, Renlong, et al. Effect of stacking fault energy on work hardening behaviors in Fe–Mn–Si–C high manganese steels by varying silicon and carbon contents. Materials & Design, 85: 707-714, (2015). [9] CHEN, C., et al. A study on aging carbide precipitation behavior of hadfield steel by dynamic elastic modulus. Materials Science and Engineering: A, 677: 446-452, (2016). [10] DODD, John. Recent developments in abrasion resistant high chromium-molybdenum irons, low-alloy manganese steels and alloyed nodular irons of importance in the extraction and utilization of energy resources. Journal of Materials for Energy Systems, 2.2: 65-76, (1980).
[11CUNAT, Pierre-Jean. Alloying elements in stainless steel and other chromium-containing alloys. ICDA, Paris, (2004).
[12] NAKAJIMA, Kenichi, et al. Simultaneous material flow analysis of nickel, chromium, and molybdenum used in alloy steel by means of input–output analysis. Environmental science & technology, 47.9: 4653-4660, (2013).
[13] LENCINA, Rodrigo, et al. Assessing wear performance of two high-carbon Hadfield steels through field tests in the mining industry. Procedia Materials Science, 9: 358-366, (2015). [14] AGUNSOYE, J. O., et al. Wear of Hadfield austenitic manganese steel casting. In: ICF12, Ottawa (2009). [15] ZAMBRANO, O. A., et al. Hot deformation of a Fe-Mn-Al-C steel susceptible of κ-carbide precipitation. Materials Science and Engineering: A, 689: 269-285, (2017). [16] KIM, Hoyoung, et al. Evolution of carbides in cold-work tool steels. Materials Characterization, 107: 376-385, (2015). | ||||
|
Statistics Article View: 417 PDF Download: 324 |
||||
