SOME FACTORS AFFECTING THE MECHANICAL CHIPPING OF TREE-BRANCHES | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 1, Volume 35, Issue 4, October 2018, Page 1165-1186 PDF (676.38 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2018.95174 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| Ibrahim Yehia1; Mohamed Omran2 | ||||
| 1Professor and Previous Head of Mechanization Systems of Ag. Operations Dept, Ag. Eng., Res. Inst., Giza, Egypt | ||||
| 2Associated Prof., Ag. Eng. Dept., Faculty, of Ag., Cairo Uni., Giza, Egypt | ||||
| Abstract | ||||
| The aim of this research is to study some factors affecting the mechanical chipping of tree-branches using a disc-chipper consists of frame, feeding duct, rotating disc with three knives, fixed knife in housing body, suction fan and 5.6 kW electric motor. The studied performance-factors are: cutting-knife speeds of 800, 1000, 1200, and 1400 rpm, clearances between rotating knives and disc of 10, 15 and 20 mm, tree-branch diameters of 30, 40, 50, 60 mm and random mixed and tree-branch moisture contents of 10, 15 and 20 % in wet base. The main results of the tested disc-chipper were summarized in the following points: (1) The maximum average of cutting length is 25.5 mm was obtained with cutting-knives speed of 800 rpm , clearance of 20 mm., tree-branches moisture content of 20 % and tree-branches diameter of 30 mm Meanwhile, the minimum average of cutting length of 6.6 mm was obtained with cutting-knives speed of 1400 rpm, clearance of 10 mm., tree-branches moisture content of 10 % and mixed branch-diameters. (2) The maximum machine-productivity of 0.4Mg/h was obtained with cutting-knives speed of 1400 rpm, clearance of 20 mm., tree-branches moisture content of 20 % and diameter of 60 mm Meanwhile, the minimum machine-productivity of 0.15 Mg/h was obtained with cutting-knives speed of 800 rpm, clearance of 10 mm., tree-branches moisture content of 10 % and mixed branch-diameters. (3) The maximum operation cost of 90.7 L.E./Mg was obtained by using tree branches diameter of 30 mm with moisture content of 10 %, clearance of 10 mm and at optimum knives-speed of 1400 rpm. Meanwhile, the minimum operation cost of 28.7 L.E./Mg was obtained by using tree-branches diameter of 60 mm with moisture content of 20 %, clearance of 20 mm at knives-speed of 1400 rpm. The results showed that the tested disc-chipper can be used to chip residues of tree trimming which expand the area of its utilization for most farm residues through the year at the optimum knives-speed of 1400 rpm which reduces the machine operating costs. | ||||
| References | ||||
|
Abo-Elasaad, G. A. 2016. Development of a rice straw bales chopper. M. Sc. Dept. of Agic. Mech. Fac. of Agriculture. Mansoura Univ.: 47 – 79.
Awady, M. N. 1978. Tractors and Farm Machines. Fac. Agric. Ain Shams Univ. 164-167.(Arabic text)
B.C.A.A.E.S. (Bulletin of Central Administration for Agricultural Extension Service) 2015, Ministry of Agric., Egypt. (in Arabic).
EL-Eraqi, M. and S. EL-Khawaga. 2003. Design and test performance of cutting machine for some crop residues. (a). Misr J. Agric. Eng., 20(1): 85 - 101.
El-Fatih, A.; E. M. Arif and A. E. Atef, 2010, Evaluate the Modified Chopper for Rice Straw Composting. J. Appl. Sci. Res., 6(8): 1125 -1131.
FAO, 2008, Animal production based on crop residues processing machines, Corporate Document, Repository, Agric. and Consumer Protection.
Ghanem, G. H. and Basiouny, M. A., 2010, Modifying a thresher for ensiling the green rice straw by shredding, Misr J. Agric. Eng., 27(2): 482-500.
Kurt, G., 1979. Engineering formulas, 3rd Ed., McGraw Hill Book N. Y.
Miu, P. I, R. Alvin; A. R. Womac; I. Cannayen, and S. Sokhansanj, 2006. Analysis of biomass comminution and separation processes in rotary equipment – a review, ASABE Ann. Int. Mtg Sponsored by ASABE Oregon Convention Center, Portland, Oregon, and Mich.
Mohamed. A. H. 2016. Development of a rice straw disc chipper, J. Soil Sci. and Agric. Eng. Mansoura Univ. 7 (10): 705 – 711.
Spinelli R., E. Cavallo, L. Eliasson, A. Facello. 2013. Comparing the efficiency of drum and disc chippers. Silva Fennica. 47(2):1-11.
Woldt, D. ; G. Schubert and H. G. Jäckel. 2004. Size reduction by means of low-speed rotary shears. Int. J. of Mineral Proc. 74: 405-415 | ||||
|
Statistics Article View: 275 PDF Download: 236 |
||||
