A THREE – DIMENSIONAL EVALUATION OF THE ACCURACY OF “EXPRESS XT” VINYL POLYSILOXANE IMPRESSION MATERIAL USING SPRAY DISINFECTION TECHNIQUE WITH IMMEDIATE AND DELAYED POURING TIME (IN VITRO STUDY)
Abd El Haliem, N., Taymour, M., Nassef, T., Zaki, A. (2016). A THREE – DIMENSIONAL EVALUATION OF THE ACCURACY OF “EXPRESS XT” VINYL POLYSILOXANE IMPRESSION MATERIAL USING SPRAY DISINFECTION TECHNIQUE WITH IMMEDIATE AND DELAYED POURING TIME (IN VITRO STUDY). EKB Journal Management System, 62(Issue 1 - January (Part 5)), 1081-1087. doi: 10.21608/edj.2016.95424
Norhan Naief Abd El Haliem; Maha Ahmed Taymour; Tamer Moneir Mousa Nassef; Amina Abd El Latif Zaki. "A THREE – DIMENSIONAL EVALUATION OF THE ACCURACY OF “EXPRESS XT” VINYL POLYSILOXANE IMPRESSION MATERIAL USING SPRAY DISINFECTION TECHNIQUE WITH IMMEDIATE AND DELAYED POURING TIME (IN VITRO STUDY)". EKB Journal Management System, 62, Issue 1 - January (Part 5), 2016, 1081-1087. doi: 10.21608/edj.2016.95424
Abd El Haliem, N., Taymour, M., Nassef, T., Zaki, A. (2016). 'A THREE – DIMENSIONAL EVALUATION OF THE ACCURACY OF “EXPRESS XT” VINYL POLYSILOXANE IMPRESSION MATERIAL USING SPRAY DISINFECTION TECHNIQUE WITH IMMEDIATE AND DELAYED POURING TIME (IN VITRO STUDY)', EKB Journal Management System, 62(Issue 1 - January (Part 5)), pp. 1081-1087. doi: 10.21608/edj.2016.95424
Abd El Haliem, N., Taymour, M., Nassef, T., Zaki, A. A THREE – DIMENSIONAL EVALUATION OF THE ACCURACY OF “EXPRESS XT” VINYL POLYSILOXANE IMPRESSION MATERIAL USING SPRAY DISINFECTION TECHNIQUE WITH IMMEDIATE AND DELAYED POURING TIME (IN VITRO STUDY). EKB Journal Management System, 2016; 62(Issue 1 - January (Part 5)): 1081-1087. doi: 10.21608/edj.2016.95424

A THREE – DIMENSIONAL EVALUATION OF THE ACCURACY OF “EXPRESS XT” VINYL POLYSILOXANE IMPRESSION MATERIAL USING SPRAY DISINFECTION TECHNIQUE WITH IMMEDIATE AND DELAYED POURING TIME (IN VITRO STUDY)

Egyptian Dental Journal
Article 5, Volume 62, Issue 1 - January (Part 5), January 2016, Page 1081-1087  XML PDF (855 K)
Document Type: Original Article
DOI: 10.21608/edj.2016.95424
View on SCiNiTO View on SCiNiTO
Authors
Norhan Naief Abd El Haliem1; Maha Ahmed Taymour2; Tamer Moneir Mousa Nassef3; Amina Abd El Latif Zakiorcid 4
1Msc Fixed Prosthodontics, Faculty of Oral and Dental Medicine, Cairo University
2Lecturer of Fixed Prosthodontics Faculty of Dentistry, Cairo University
3Lecturer of Computer and Software Faculty of Engineering, Misr University for Science and Technology
4Professor of Fixed Prosthodontics Faculty of Oral and Dental Medicine, Cairo University
Abstract
objectives: The aim of this study was to evaluate the dimensional accuracy of the recently introduced vinyl polysiloxane impression material “Express XT” when subjected to sprayed disinfection with Cavicide1 disinfectant solution at two different pouring times. Using three dimensional DicoMesher software version3.
 
methods: A total of twenty impressions of a standardized stainless steel mold were made using Express XT impression material in specially fabricated trays. The impressions were subjected to spray disinfection protocol using cavicide 1 disinfectant solution and then divided according to times of pouring into two groups immediate pour according to manufactures instructions and One-week delay pouring. Impressions were poured with a type IV extra hard dental stone. All measurements were performed on the photos of the produced cast by DicoMesher software a computer software program allowing three dimension recording. Results were statistically analyzed
 
results: Immediate pouring time showed the lowest mean overall dimensional changes while delayed pouring time showed higher mean shrinkage. However, there was no statistically significant difference between the overall dimensional changes of the two groups.
conclusion: Within the limitation of this study we concluded that different pouring times did not harm the dimensional stability of the die material.
Statistics
Article View: 153
PDF Download: 234