OPTMIZING THE PERFORMANCE OF PLOT SEEDER MACHINE TO SUIT WHEAT SEED PRODUCTION

Fouda, T.; Salah El-Din, I.; Derbala, A.; Darwesh, M.; El-Kolaly, W.

doi:10.21608/mjae.2017.96366

	OPTMIZING THE PERFORMANCE OF PLOT SEEDER MACHINE TO SUIT WHEAT SEED PRODUCTION
Misr Journal of Agricultural Engineering
Article 5, Volume 34, Issue 2, April 2017, Page 635-650 PDF (1.04 MB)
Document Type: Original Article
DOI: 10.21608/mjae.2017.96366
View on SCiNiTO
Authors
T. Fouda¹; I. Salah El-Din²; A. Derbala³; M. Darwesh³; W. El-Kolaly⁴
¹Prof. of Agric. Eng. Dept. , Fac. of Ag., Tanta. Univ., Egypt.
²Prof. of Agric. Eng. Res. Inst., Agric. Res. Center, Dokki, Egypt
³Assoc. Prof. of Agric. Eng. Dept., Fac. of Ag. , Tanta. Univ., Egypt.
⁴Postgraduate of Agric. Eng. Dept., Fac. of Ag. , Tanta. Univ., Egypt.
Abstract
The plot seeders have a variety of distribution systems makes it possible to distribute the seed for a plot over multiple rows and many options allows you to customize the machine for many different applications. So when used a plot seeder to suitable for cultivation of wheat seeds must adjustment transmission mechanism and a feed cartridges diameter, as well as seeding shaft and distributor cone rotates. This study carried out to improve the performance of plot seeder and minimize the total damage during wheat seed production processes. The treatments under this study were at four diameters of feed cartridges (10, 15, 20 and 25 mm Ø), two kinds of distributor plat (distributor plat with and without partition)and three groups of sowing transmission. The variation coefficient of seeds and seeds damage were measured. The seeds damage generally increased with the decrease of feed cartridge from 15.6% at feed cartridge diameter (10 mm Ø) to 2.4% at feed cartridge diameter (25 mm Ø). Also seeds damage increased with distributor plat with partition. That was 15.6% with distributor plat with partition and 14.6% without partition. The variation coefficient of seeds decreases at diameter of feed cartridge (20 mm Ø) with distributor plat without partition and the first group of sowing transmission.


References
Abu – Shieshaa R., Kholief R., and EL – Meseery A. A., (2007), A study of some physical and mechanical properties of seed Melon seed, Misr J.Ag. Eng., 24(3):575 – 592. El-Raie; A.E.S.; N. A. Hendawy and A.Z. Taib, (1996); Study of physical and engineering properties for some agricultural products. Misr. J. Ag. Eng., 13 (1) : 211-226. Liu Shuguang, Shang Shuqi, Yang Ranbing (2010). Test and optimization of parameters for the storing device of plot seeder[J]. Transactions of the Chinese Society of Agricultural Engineering (Transactions of the CSAE), 2010, 26(9): 101 -107. Mohsenin, N. N., (1986); Physical Properties of Plant and Animal Materials, Gordon and Breach Sc. Pub., N. Y. pp. 734. Raheman, H. and U. singh (2005): A manual Drawn multi-crop Drum seeder for dry land. Agricultural and food engineering department, Indian institute of tech : 58-63. Singh, R. C and D. C. Saraswat (2005). Optimization of design and operational parameters of a pneumatic seed metering deice for planting cottonseeds. Bio-systems Engineering, 92(4): 429-433. Soliman N.S.(1994). Effect of moisture content on angle of repose of Paddy rice and its products. Misr, J. Ag. Eng. 11(1):163-173. Zoltán H. (2007). Examination of cone-belt dispenser7^th international multidisciplinary conference Baia Mare, Romania, May 17-18, 2007 ISSN-1224-3264
Statistics Article View: 167 PDF Download: 232