THE SCREW WEAR INFLUENCE ON THE PERFORMANCE OF AN OILSEED EXPELLER
El-Ashry, A., Tawfk, M. (2016). THE SCREW WEAR INFLUENCE ON THE PERFORMANCE OF AN OILSEED EXPELLER. EKB Journal Management System, 33(4), 1315-1328. doi: 10.21608/mjae.2016.97599
A. S. El-Ashry; M.A. Tawfk. "THE SCREW WEAR INFLUENCE ON THE PERFORMANCE OF AN OILSEED EXPELLER". EKB Journal Management System, 33, 4, 2016, 1315-1328. doi: 10.21608/mjae.2016.97599
El-Ashry, A., Tawfk, M. (2016). 'THE SCREW WEAR INFLUENCE ON THE PERFORMANCE OF AN OILSEED EXPELLER', EKB Journal Management System, 33(4), pp. 1315-1328. doi: 10.21608/mjae.2016.97599
El-Ashry, A., Tawfk, M. THE SCREW WEAR INFLUENCE ON THE PERFORMANCE OF AN OILSEED EXPELLER. EKB Journal Management System, 2016; 33(4): 1315-1328. doi: 10.21608/mjae.2016.97599

THE SCREW WEAR INFLUENCE ON THE PERFORMANCE OF AN OILSEED EXPELLER

Misr Journal of Agricultural Engineering
Article 8, Volume 33, Issue 4, October 2016, Page 1315-1328  XML PDF (900.79 K)
Document Type: Original Article
DOI: 10.21608/mjae.2016.97599
View on SCiNiTO View on SCiNiTO
Authors
A. S. El-Ashry1; M.A. Tawfk2
1Professor, Agric. Eng. Res. Inst.(AEnRI), Dokki, Giza, Egypt.
2Assistant. Prof., Agric. Eng. Dept., Fac. of Agric., Zagazig Univ., Egypt.
Abstract
The main objective of the present study is investigating the influence of the tapered screw hardening treatment and screw operating hours on the abrasive wear at three different zones of feeding (A), crushing (B) and pressing(C) on the screw as well as the expeller performance during the oil expression processfor determining the optimum time for the screw replacement. This study was carried out to compare the performance of two types of the tapered screws, the hardened (HS) and Non-hardened (NHS) to press flax seeds during 400 h of working at the recommended operating conditions of 9% for seed moisture content, 30 rpm for screw speed and 0.4 mm for outlet clearance. The obtained results revealed that, the HS would decrease the wear after 400 h of oil expression by about 30.54, 26.22 and 35% at A, B and C zones, respectively compared to NHS. The using of HS would increase the feeding capacity, expressed oil and expression efficiency by about 6.7, 7.44 and 5.56%, respectively more than the NHS. Also, the using of HS would decrease the oil in cake, and consumed energy by about 11.75 and 6.7%, respectively compared to the NHS. Ultimately, it is suggested to make replacement to the tapered screw with a new one after 300 and 400 operating hours for the NHS and HS, respectively, this mean that, the HS may give 100 h of oil expression more than the NHS.
Keywords
Flax seeds; expeller; tapered screw; abrasive wear; hardening; machine performance
References
Bamgboye, A.I.  and Adejumo, A.O. (2007). Development of a Sunflower Oil Expeller. Agricultural Engineering International: the CIGR E-journal, Vol. IX, pp. 1-7.

El-Ashry, A.S.(1999). Development of a simple machine for expression of some oilseeds. Ph.D Thesis, Fac. of Agric., Minoufiya Univ., Egypt.

El-Sahrigi, A. F.,  S. M. Sharaf, M.A. Mohamed and A.S. A. El-Ashry (2005). Development of a small screw expeller for extracting oil from linseed. Misr Journal of Ag. Eng., 22(2):699-714.

Khurmi, R.S and J.K. Gupta (2005). Machine Design. A Textbook 14th ed., Eurasia Publishing House (PVT.) Ltd., Ram Nagar, New Delhi-110 055.42-44 pp.

Maleque, M. A. and M. S. Salit (2013). Material Selection and Design. A Textbook 1st , chap 2: Failure Due to Wear. Springer, 38pp.

Neale, M. J. (1995). The  Tribology. Handbook, 2nd  ed., Jordan Hill, P.E 8.1-E 8.3 Oxford, London, UK.

Sari, P. (2006). Preliminary design and construction of a prototype canola seed oil extraction machine. M.Sc. Thesis, Graduate School of Natural and Applied Sciences, Middle East Technical Univ., Turkey.

Wessiling, B. S., S. Schroder, H. Gleeson, D. Merkle and F. Baron (1996). Scientific engineering of anti- Corrosion coating systems based on organic metals (polyaniline), Metal and Corrosion,47; 439.

Statistics
Article View: 112
PDF Download: 173