NEW APPARATUS TO RAISE THE PERFORMANCE OF ENGINE COOLING WATER CYCLE | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 16, Volume 32, Issue 4, October 2015, Page 1671-1684 PDF (1.34 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2015.97841 | ||||
 View on SCiNiTO | ||||
| Author | ||||
| T. H. EL-Shabrawy | ||||
| Lecturer of Ag. Eng., Ag. Eng. dept., Fac. of Ag., Mansoura Univ., Egypt. | ||||
| Abstract | ||||
| Internal combustion engines consider as a power source of all machines in agricultural operations. To obtain the optimum performance of these engines there temperature must be maintained at the optimum level. To achieve the previous aim, the engine cooling system must be responsible for the absorption of excess heat from the engines particularly in hot regions. Therefore, this study was conducted in order to solve a problem of failure engine water cooling cycle in warm areas by appending an additional unit to the engine cooling water circuit consisting of an additional thermally insulated tank of water cooled by two pieces of peltier sheets and electric cooling fans. When engine temperature rise above the allowed level, the cooling water path throw the assistant cooling apparatus (peltier cooling unit) to maintain the engine temperature at the ideal level. Four main parameters were taken in this study, five levels of electric current intensity CI (1, 2, 3, 4 and 5 Ampere), four levels of water flow rate FR (0.5, 1, 1.5 and 2 liter/min.), four levels of temperature of inlet water WT (75o, 80o, 85o and 90oC), and two types of flow water FT (free flow and in serpentine). Absorbed heat energy Q=kJ/min was calculated at different levels of studied parameters under study. The obtained results showed that, the peltier sheets with second type of flow water (in serpentine) gained an effective decrease in water temperature, this condition decreased with the increase of inlet water temperature WT above 85oC. The highest value of absorbed heat energy Q =502.2 kJ/min was gained with (CI5 = 5 amp.), (FR4 = 2 lit/min.) and (WT1 = 75o) at serpentine type of flow water rate (FT1). | ||||
| References | ||||
|
Abdelghaffar, W. A.; M. N. Saeed; M. M. Osman and A. I. Abdelfattah (2002), Effects of coolant temperature on the performance and emissions of a diesel engine. pp. 187-197 (American Society of Mechanical Engineers, New York, NY 10016-5990, United States.
Brace, C. J.; Burnham, H.; Wijetunge, R. S.; Vaughan, N. D.; Wright, K. and Blight, D. (2001), Integrated Cooling systems for Passenger vehicles, SAE Paper Number 2001-01-1248..
Chalgren, R. D. J. (2004), Thermal comfort and Engine warm up Optimization of a low flow advanced Thermal management system, SAE Paper Number 2001-01-0047.
Couetouse, H. and Gentile, D. (1992), Cooling System control in Automotive Engines, SAE Paper Number 920788.
Gogineni, P.; Gada, V. and Babu, S. (2014), Cooling systems in automobiles & cars. International journal of advances in engineering & technology (IJEAT) ISSN: 2249 – 8958, Volume-2, Issue-4, April 2013.
Heywood, J. (1988), Internal combustion engine fundamentals, New York, NY:McGraw-Hill.
Mirko, B. (2014), "Principles of heat transfer in internal combustion engines from a modeling stand point" PhD Thesis, Chalmers university of technology, Gothenburg-Sweden.
Pang, H. H. and Brace, C. J. (2004), Review of engine cooling technologies for modern engines. Proceedings of the Institution of Mechanical Engineers Part D-Journal of Automobile Engineering, 2004, 218(D11), 1209-1215.
Tonye, K. J.; Mohammed, M. and Fredy, H. (2013), A review of considerations in cooling systems calculations with variable coolant density and specific heat. International journal of advances in engineering & technology. May (2013) Vol. 6, ISSN 1963 – 2231.
Wusner, Y.; Chen, B. and Hsieh, F. (2009), Heat transfer model for small-scale water cooled spark-ignition four-stroke engines. International Journal of heat and mass transfer, Vol. 52, pp. 1875-1886. | ||||
|
Statistics Article View: 124 PDF Download: 205 |
||||
