SEEDER EQUIPPED WITH SEEDS DELIVERY MECHANISM DEPENDING ON AN OSCILLATING MOTIVATION UNIT | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 21, Volume 32, Issue 4, October 2015, Page 1761-1774 PDF (812.92 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2015.97872 | ||||
 View on SCiNiTO | ||||
| Author | ||||
| Z. E. Ismail | ||||
| Prof. of Ag. Eng., Ag. Eng. dept., Fac. of Ag., Mansoura Univ., Egypt. | ||||
| Abstract | ||||
| Seeder equipped with seeds delivery mechanism depending on an oscillating motivation unit was constructed and tested under indoor experiments. The main components of investigated prototype are; seeds delivery mechanism equipped with oscillating unit, metering device and mobile trolley as power unit. On the base of a corn fertilizer unit a tray was conducted to plant seeds of Phaseolus. Four seeds delivery speeds (SDS) of 0.4; 0.5; 0.6 and 0.7 m/s with three hole span (HS) of 50, 100 and 150 mm and three different of the delivery tubes lengths (TL) of 300, 400 and 500 mm were identified as independents variables. The influence of a reciprocating motivation unit on the seeds distribution evaluated by calculating seeds miss index (MI), multiples index (DI), quality of feed index (FI) and precisions index (PI) in spacing for kidney bean (Phaseolus Vulgaris) seeds. The results indicated that increasing the seeds delivery speed 1.75 times MI increased by about 3.6 times at HS=150 mm. The appropriate relation was found at SDS=0.5m/s and HS=100mm. Also, the data revealed a direct proportion between DI and each of SDS and TL. The feed index (FI %) recorded the highest values (95.9%) at SDS of 0.5m/s and HS of 150mm. For example by increasing the SDS 1.5 times FI % decrement by about 0.9 times. | ||||
| References | ||||
|
Ess, D.R.; S.E. Hawkins; J.C. Young and E.P. Christmas (2005). Evaluation of the performance of a belt metering system for soybeans planted with a grain drill. Applied Engineering in Agriculture. 21: 965-969.
Gebresenhet, G. and H. Jonsson (1992). Performance of seed drill coulters in relation to speed, depth and rake angle. J. Agric. Eng. Res. 52: 121-145.
Gratton, J.; Y. Chen and S. Tessier (2003). Design of a spring-loaded down force system for a no-till seed opener. Canadian Bio-systems Engineering. 45: 29-35.
Guler, I.E. (2005). Effects of flute diameter, fluted roll length, and speed on alfalfa seed flow. Applied Engineering in Agriculture. 21: 5-7.
Heege, H.J. (1993). Seeding methods performance for cereals, rape, and beans. Transaction of the ASAE. 36: 653-661.
Ismail, Z.E. (2011). Punch planter: specification and evaluation. Misr. J. Ag. Eng., 28(4): 782-795.
Ismail, Z.E., E.H. El-Hanify and N.K. Ismail (2009). The utilization of a metering plate device for cowpea planting. J. Agric. Sci. Mansoura Univ. 34(5): 5853-5867.
Ismail, Z.E. and E.H. El-Hanify (2009). Construction and testing the seed-punch planter. Misr. J. Ag. Eng., 26(2): 597-607.
Ismail, Z.E. (2004). Developing the metering unit of the pneumatic planter "project financed by Researching Unit of Mansoura University".
Janelle, L., C. Lague and S. Tessier. 1993. Seeding tool design for no-tillage conditions in North-East. ASAE Paper No. 93-1561. St. Joseph, MI: ASAE.
Karayel, D.; M. Wiesehoff; A. Ozmerzi and J. Muller (2006). Laboratory measurement of seed drill, seed spacing and velocity of fall of seed using high-speed camera system. Computers and Electronics in Agriculture. 50: 89-96.
Molin, J.P.; L.L. Bashford, K. Von Bargen and L.I. Leviticus (2002). Design and evaluation of a punch planter for no-till systems. Transactions of the ASAE 41(2): 307-314.
Molin, J. P., L. L. Bashford, R. D. Grisso and A. J. Jones (1998). Population rate changes and other evaluation parameters for a punch planter prototype. Transactions of the ASAE 41(5): 1265-1270
Ozmerzi, A.; D. Karayel and M. Topakci (2002). Effect of sowing depth on precision seeder uniformity. Bio-systems Eng. 82: 227-230.
Ryu, I.H. and K.U. Kim (1998). Design of roller type metering device for precision planting. Transaction of the ASAE. 41: 923-930.
Sawant, S.D. (1972). Design and basic studies of a plunger-type planter. Ph.D. diss. University Park, Pa.: Pennsylvania State University.
Schueller, J.K. (1992). A review and integrating analysis of spatially-variable control of crop production. Fertilizer Res. 33: 1-34.
Shaw, L.N. and K.H. Kromer (1987). Revolving spade planter soil opener. ASAE Paper No. 87-1019. St. Joseph, Mich.: ASAE.
Solie, J.B. 1991. Design and field testing two ultra-narrow row grain drills. ASAE Paper No. 91-1007. St. Joseph, MI: ASAE. | ||||
|
Statistics Article View: 134 PDF Download: 245 |
||||
