DEVELOPMENT OF A SUGAR BEET TOPPER | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 2, Volume 31, Issue 3, July 2014, Page 729-752 PDF (1.59 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2014.98892 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| Y. R. Yusuf; M. Qutob; A. M. El-Beba | ||||
| Researcher. Ag. Eng. Res. Inst. (AEnRI), Giza, Egypt. | ||||
| Abstract | ||||
| The aim of this research is to develop and evaluate a topper unit for sugarbeet suitable for Egyptian conditions. Field experiments were carried out at El-Serw Agric. Res. Station, Damietta Governorate during 2013/2014 season. The performance of the developed topper unit was evaluated at different speed ratios of 0.007, 0.0076, 0.0080 and 0.0085 under knives positions; faced (F) and edged (E) and flails number solo (S) and doubled (D). Different flail lengths of 15, 20, 25 and 30 cm were tested. Over topping, under topping beets, un-topped beets, damaged beets, topping efficiency, actual field capacity, field efficiency, energy requirement and total costs were estimated. Due to increasing speed ratio increased actual field capacity and field eff. Both doubled and faced flails showed the best results under all treatments. Generally, the results recommended that topper unit should be used at speed ratio of 0.0085 with doubled-faced-flail (DFF) that recorded highest value of topping eff. (97.30%). On the other hand, the lowest value for over topping beet (2.4%), undertopping beets (2.8%), un-topped beets (2.2%) and damaged beets (2.77% ) were recorded. Hence, the best value of actual field capacity (0.92 fed/h) and field eff.(83.4%) were recorded at speed ratio of (0.0085). Energy requirement decreased by 13.22 % while total costs decreased by 78.27% comparing to manual topping costs. Flail length of 25 cm showed the desirable results with all treatments. Doubling and facing flails position had a high significant effect on all treatments. | ||||
| References | ||||
|
Abd-Rabou.A.F., (2004). Manufacturing a small machine to suit harvesting sugar beet under Egyptian conditions. Ph. D., Thesis. Agric. Mech. Dept., Fac. Agric., Kafr El – Sheikh. Tanta Univ.
Abou-shieshaa, R. R., (1996). A study on harvesting mechanization of sugar beet. Ph.D., Thesis. Agric. Mech. Dept., Fac. Agric. Kafr El–Sheikh. Tanta Univ.
Allam, A. I., A. M. Nour., and M. A. Farag., (1988). Prospective of sugar beet mechanical growing. Agric. Res. Review., Agric. Res. Center., Giza., Egypt, 66 (3): 537-543.
Aly, A.H., (1998). Design and development of a sugar beet topper. Ph.D., Thesis. Agric. Mech . Dept., Fac. Agric., Ain Shams Univ.
ASABE D497.7.( 2011). Agricultural Machinery Management Data. ASABE D497.7.
Awad, M.A., 2006. Developing of a pulling out mechanism for harvesting sugar beet crop. Ph.D. Thesis. Agric. Eng. Dept., Fac. Agric., Mansoura Univ.
Bahnas, O.T., (2006). The mechanical sugar beet harvest requirements in the reclaimed lands. Misr. J. Agric. Eng., 23(4): 909 – 928.
Bulich-C; and W. Brinkmann, (1983). Harvesting losses in sugar beet are still too high! DLG-Mitteilungen 98:16, 888-890.
Cracaleanu-M, M. Sirbu, and A. Szekeli, (1995). Economic efficiency of sugar beet mechanized harvesting. Cercetari- Agronomice- in-Moldova. Romania, 28:3-4, 19-23.
EL-Sherif, R. R. 1996. A study on harvesting mechanization of Sugar beet- Unpubl. thesis. Fac. of Agric., Kafr El-Sheikh, Tanta Univ., Egypt. 85:90.
Hunt, D. (1983): Farm power and machinery management. 8th Ed. Iowa state Univ., Press Ames, USA. Ames, Iowa, USA: 364-368.
Ismail, Z. E., Y. M. El –Hadidi. and M.A. El – Saadany., (1993). The utilization of a developed disc mower to remove the vegetative tops of some tuber crops. Misr. J. Ag. Eng., 10(3): 508 – 524.
Kanafojski, C. Z. and T. Karwowski., (1976). Agricultural machine theory and construction (vol 2: Crop – harvesting machines). Published for the U.S. department of agriculture and the national science foundation, Washington, D.C. P: 830-920
Khodeir, M.A.A., (2002). Development of a small machine suitable for harvest sugar beet under Egyptian conditions. Ph.D., Thesis. Agric. Mechanization. Dept., Fac. Agric., Kafr El – Sheikh, Tanta Univ.
Mady, M.A., (2001). Mechanization of some operations for sugar beet production. Misr. J. Ag. Eng., 18 (2): 339– 355.
O’Dogherty, M. J. (1986). Journal of Agricultural Engineering Research., 35: 1, 55-66; 11 ref.
Persson, S. (1987). Mechanics of cutting plant material. St. Joseph, Michigan: American Society of Agricultural Engineers. Plinius Gaius, S. AD 77-79. Naturalis Historiæ. In 26. ed.
Raininko, K., (1990). Sweeden sugar beet production, J. of sugar. 1 (29) 32:62.
Richey, C.B., P. Jacobson. and C. Hall., (1961). Agricultural engineers’Hand book. McGrow – Hill books Co, INC. New – York. USA. P:270 – 274.
Sharobeem,Y.F; I.M.Abd-El-Tawwab and S. EL-Khawaga (2003). Design and construction of a 3-row lifting machine for sugar beet. Misr. J. Ag. Eng., 20(4): 980-992.
Srivastava, A. k., C. E. Goering., P. R. Rohrbach., (1998). Engineering principles of agricultural machines. ASAE.and Textbook, No (6). Pub. American Society of Agricultural Engineers. P: 45-60
Srivastava, A. K., C. E. Goering and R. P. Rohrbach. (2006). Hay and Forage Harvesting. In Engineering principles of agricultural machines, 325. ed. Anonymous , St. Joseph, Michigan: American Society of Agricultural Engineers.
Sugar crops council. 2005. Annual report on sugar crops and sugar production in Egypt. (In Arabic). Minster of Agric and land reclamation. P: 18.
Tayel, S.A., A.A. El-Nakeeb., M.F. Khairy., and N.M. El- Bialee, (2009). Develop and evaluate sugar beet topping unit to suit in small holdings. Misr J. Ag. Eng., 26(1): 44- 55 | ||||
|
Statistics Article View: 110 PDF Download: 254 |
||||
