SELECTING OPTIMUM METHOD FOR SOWING CANOLA CROP (BRASSICA RAPUSL) | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 5, Volume 30, Issue 4, October 2013, Page 975-990 PDF (1.18 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2013.99569 | ||||
 View on SCiNiTO | ||||
| Author | ||||
| A. A. I . AL-Gezawe | ||||
| Researcher, Ag. Eng. Res. Inst., Ag. Res. Center, Dokki, Giza, Egypt. | ||||
| Abstract | ||||
| The aim of this research is to study the effect of some manual and mechanical planting methods on canola crop yield. Three manual as well as two mechanical methods of planting canola crop were conducted. Mechanical planting methods were carried out under four different forward speed. Manual and mechanical planting methods were evaluated in terms of field capacity and field efficiency, plant characteristics, crop yield, energy requirements and planting cost. The main results in this study can be summarized in the following points: *The heihest yield (1580 kg/fed) was obtained by using pneumatic planter with row spacing of 40 cm, while lowest yield (924 kg/fed)was obtained by using manual broadcasting method. *The heihest value of cost per feddan (300 L.E/fed)was obtained by using manual transplanting method, while the lowest value(14.8L.E./fed)was obtained by using seed-drill. It is recommended to use the pneumatic planter at a forward speed 4 km/h for planting canola crop to maximize crop yield and minimize planting cost. | ||||
| References | ||||
|
Abdou, F. M; (1995): Effect of seed-bed preparation and plant
population on onion crop production, The Role of Ag. Eng. IN
Sustainable Development 3rd Conf. of Misr Society of Ag.Eng,
5-6 October 1995: 153 – 162
Awady, M. N. (1978): Tractor and farm machinery. Text book, Faculty of Agriculture, Ain-ShamsUniversity. Pp: 164-167.
Awady, M. N; E. Y. Ghoneim and A. I. Hashish (1982): A critical comparison between wheat combine harvester under Egyptian conditions. R. S. No. 1920, Ain-ShamsUniversity. (FAO) J.
El-Sayed, G.H; M.A., El- Attar, S. E. ,Badr, and I.,Yehia, 2001.Effect of some mechanical planting systemes on canola crop yield, 9 th Conf of Misr Soc. of Ag. 10- 12 December, under Publishing .
El-Shal, M. S.(1987):A study on usability ofpneumatic planter under Egyption .
Gamal, H. E., M. A. El-Attar., S. E. Bader and I. Yahia (2001). Effect of mechanical planting system on Canola crop yield. Misr J. Agric. Eng., 18 (4): 163-172 .
Gomaa, S.M.(2003):Performance evaluation of pneumatic and mechanical planters for cowpea planting. Misr J.Ag.Eng.,20 (4):965 – 979
Hunt, D. (1983): Farm power and machinery management. 8th Ed. Iowa state Univ., Press Ames, USA. Ames, Iowa, USA: 364-368
Imbabi, A. T., (1996) :Effect of field dimension on the performance and productivity of the planter machine for planting sun flower seeds in flat and furrow soil. . Misr J.Ag.Eng.13 (3) july.
Jamal M. khan, Rian A. Khattak and M. Asim Khan (2000): Influence of sowing methods on the productivity of canola grown in saline field. Pakistan Journal of biological. 3 (4) : 687-691 .
Kepner, R. A; K. Bainer and E. L. Barger (1982): Principles of farm machinery. 3rd Ed., AVI Pub. Com. Inc., Westport. 527pp.
Moustafa, E.M.(1993): Mechanization of soybean crop. M. Sc. Thesis, fac. Ag. Zagazig Univ.
Sharma, D.N., Bansal, N.K., and Jain, M. I., (1983): Design, development and testing of bullock-drawn, row seed-cum –fertilizer drill, A M A 14(2): 37 – 40.
Srrivastava, A.C,(1993): Elements of farm machinery. Oxford and IBH publishing Co.New Delhi.
Yehia, I.,S.E. Bader; and A. Lotfy (2005):Effect of some planting systems on cowpea crop productivity. The 13 thconference of the Misr society of Ag. Eng. 14-15 December. 670- 678 . | ||||
|
Statistics Article View: 127 PDF Download: 207 |
||||
