EFFECT OF AIR FLOW RATE OF WINNOWING FAN ON PERFORMANCE OF RICE COMBINE HARVESTER MACHINE | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 5, Volume 31, Issue 2, April 2014, Page 425-438 PDF (660.18 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2014.99580 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M.A. El- Attar; M.A. Khodeir; A.A. Soliman; H. El-Khateeb | ||||
| Agric. Eng. Res. Inst., El-Dokki – Giza - Egypt. | ||||
| Abstract | ||||
| Field experiments were carried out at the experimental field of Rice Mechanization center, Meet El-Deeba, kafre El-Sheikh Governorate, Egypt. Japanese combine harvesting machine, yanmar model CA- 385 (hold-in), cutting width 1400 mm, crawler traveling unit, adjusted pick tines and star wheels, were tested at three air flow rates of (0.25, 0.32 and 0.40 m3/s) and three different forward speeds of (0.94,1.62 and 2.88 km/h). The combine test to harvest rice variety (Sakha 101). The results revealed that all kinds of losses (header and threshing) was minimum of 0.69 and 0.90% at forward speed of 0.94 km/h. Also, the lowest value of cleaning and total losses was 0.30 and 1.89% at air flow rate 0.25 m3/s and forward speed of 0.94 km/h, respectively. The highest value of combine performance efficiency was 98.0% at air flow rate of 0.25m3/s and forward speed of 0.94km/h. By decreasing the air flow rate from 0.40. 0.32 and 0.25 m3/s tends to increase the whole grain from (79.2, 80.7 and 84.3%), empty grain form (0.44, 0.55 and 0.81%), impurity from (0.35, 0.51 and 1.0%) and grain with pedicel from (8.3, 13.8 and 16.4%), respectively, at forward speed of 0.94 km/h. Increasing the forward speed from 0.94, 1.62 and 2.88 km/h tends to decrease the criterion cost from 99.7,98.2and 97.3 LE/fed. | ||||
| References | ||||
|
Agricultural research center Issue, 2006, Technical Recommendation for Rice crop, Ministry of Agic., Rice Prog. Issue No. 1014, Egypt: 5-7.
Afify, M.K., A. Nada and W.M.Mechail (2000). Selection the proper system of planting and harvesting rice crop. Misr J.Ag. Eng., 17 (2): 388-400.
Badr, S., H.Gindy; B. Hemido and A.M.El-lithy (2007). Planting and Harvesting Method Effects on Rice Productivity. Misr J.Ag. Eng., 24 (2): 318-326.
El-Awady, M.N.; E.Y. Ghoneim and I.Hashish (1982). A critical comparison between wheat combine harvesters under Egyptian conditions. Res. Bul. No. 1920 Col. Ag. An –Shams univ., 13p.
El-Khateeb, H.A. (2005). A study on performance of axial flow combine harvester in rice crop harvesting. Misr J. Ag. Eng.,22(4):381-401.
El-Nakib, A.A.; Z.Y.Abdel-Lateef; A.A. El-Messery and A. Khateeb (2003a). Mechanical harvesting losses in rice crop using combine harvester. Misr J.Ag. Eng., 20 (4): 889-907.
El-Raie, A.S.; A. Taieb, and M. Atallah (2012). Development of threshing system in combine harvester for improving of its peformance efficiency in rice threshing. Misr J. Ag. Eng., 29 (1): 143-178.
Kamel, O.M. (1994). Rice harvesting losses utilization two different harvesting techniques of japanes. Misr J. Ag. Eng., 16 (4): 237-251.
Kepner, R.A., R. Bainer and E.L. Barger (1982). Principles of farm machinery. 4th. Ed. John W.and Sons, Ins: 381-428.
Morad, M.M. and T.fouda (2003). Development of long-axial flow rice thresher shaft for minimum threshing power. Misr J. Ag. Eng., 20 (2): 391-404. | ||||
|
Statistics Article View: 193 PDF Download: 191 |
||||
