PERFORMANCE OF A TRACTOR MOUNTED SUGARCANE HARVESTER | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 3, Volume 27, Issue 4, October 2010, Page 1034-1047 PDF (715.39 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2010.104540 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| S.A. Tayel1; A.A. El-Nakib1; H.A. Abdel Mawla2; M.H.A. Hassan3 | ||||
| 1Prof. of Agric. Engin. Dep., Faculty of Agriculture, AL-Azhar Univ., Egypt. | ||||
| 2Prof. and head of Agric. Engin. Dep., Faculty of Agriculture, AL-Azhar Univ. Assuite, Egypt. | ||||
| 3Assoc. lecture of Agric. Engin. Dep., Faculty of Agriculture, AL-Azhar Univ. Assuite, Egypt. | ||||
| Abstract | ||||
| A single row tractor mounted sugarcane harvester was fabricated and tested in the field. The unit consists of a frame, a base cutter and windrowing guide. It operated by the tractor PTO. The experiments were carried out at shandawill experiments station, Sohag governorate to determine of machine performance. The results indicated that: 1- Increasing forward speed from 2.37 to 3.75 km/h increased the total losses of sugarcane yield. Higher forward speed decreased cutting and harvesting efficiencies. 2-Decreasing the star wheel height of windrowing guide, the collecting efficiency increased. 3- Minimum total losses were 8.313 ton/fed. recorded at forward speed 2.37 km/hr and oblique angle of knife 30°. Maximum cutting efficiency was 98.46 % and harvesting efficiency was 98.86 % achieved at forward speed 2.37 km/h and oblique angle of knife 30°. Higher the collecting efficiency was 70.69 % achieved at star wheel height 105 cm. | ||||
| References | ||||
|
Abdel-Mawla H. A. and El-Geddawy I. (1997) Feasability of mechanical cane harvesting in Egypt. MSAE 5th conf, October 1997.
Awady M.N., S. M. Abd El Aal, M.A. Abd El Maksoud and A. A. Foad (1996). Evaluation of performance of a double-knife mower. MSAE. Vol 13(2):327-352.
Blackburn, F. (1984). Sugar-cane, Longman Inc., New York, U.S.A.
Eiland B. B. and J. E. Clayton (1983) Unburned and burned sugarcane harvesting in Florida Trans. ASAE (26) 5: 1331-1339
El-Nakib, A. A.; A. F. El-Sahrigi and H. A. Abdel-.Mawla (1996). Physical properties of sugar cane: their relation to mechanization. MSAE Exploiation of modem tech. In field of Agric. Eng. 4th Conference of Misr Society of Ag. Eng., 28 October: 63-78.
Gupta, C.P., L. Lwin and T.Kiatiwait (1992) Development of a self-propelled single-axle sugarcane harvester. Applied Engineering in Agriculture.Vol:12(4):427-434 pp.
Gupta, C. P. and M.F. Oduori (1992) Degin of the revolving knife-type sugarcane base cutter. Transactions of the ASAE. Vol. 35(6): 1747-1752.
Hanna, G.B., A.E. Suliman, S.M. Younis and A.Z. Taib (1985). Evaluation of different mechanical methods of cotton stalks removal.MSAE. Vol 2(1):3-25.
Iqbal Hossain S.M.,M.A. Zaman, S.U.K.Eusufzai and M.Abdullah (1996) Status and prospect of mechanization of sugarcane cultivation in Bangladech, AMA, Vol.27 No.(3):68-72.
Kanafojski C. Z. and T. Karwowski (1976) Agriculture machine, theory and construction. Vol. 2. Published for the U.S. department of agriculture and the national science foundation, Washington, D.C.
Kroes, S. (1997) The cutting of sugarcane. PhD Thesis. University of Southern Queensland. (C.F.Mello, R. da C., and Harris, H., 2003).
Mello, R. da. C., and H. Harris (2000). Cane damage and mass losses for conventional and serrated base cutter blades. Proceedings of Australian Society of Sugar Cane echnologists 22: 84- 91.
Mello, R. da C. and H. Harris (2003) Performance of base cutter of sugarcane cane harvester with angled and serrated blades. Revista Brasileira de Engenharia Agricola e Ambiental, Vol.7 No.(2), p.355-358.
Smit,M. DE L., M.F. Coetsee and S.H.E. Davis (2001). Energy expenditure and economy of movement of sugarcane cutters in burnt and green cane. Proce.S. Afr. Sug. Technol. Ass (75) pp.46-50. | ||||
|
Statistics Article View: 142 PDF Download: 219 |
||||
