DEVELOPING AND MAXIMIZING THE PERFORMANCE OF LOCAL THRESHING MACHINE FOR SMALL HOLDING TO SUIT CHOPPING AND SHREDDING CROPS RESIDUES | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 37, Volume 27, Issue 4, October 2010, Page 1588-1608 PDF (1.06 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2010.105073 | ||||
 View on SCiNiTO | ||||
| Author | ||||
| Wagdy Zaghlool El-Haddad | ||||
| Researcher, Agric. Eng. Res., Inst., (AEnRI), El-Giza, Egypt. | ||||
| Abstract | ||||
| Stationary threshing and winnowing machine model El-Haddad-WZ-1 for small holding was designed by El-Haddad, 2000 in Agricultural Engineering Dept., Faculty of Agric., Kafr El-Sheikh University. It was tested in Rice Mechanization Center for threshing and winnowing of rice crop. It was used to chopandshred rice straw crop tomaximize the performance of this machine and increasing yearly working hours, Results of the original machine showed that, it can not cut rice straw into small pieces without accumulation problems occurred in the threshing chamber especially with feeding of complete stalks sample at high moisture content. This problem causes wasting time, less productivity, and increase cost. Consequently, it is necessary to develop this machine for the young farmer to cut some crop residues as rice straw, corn stalks and cotton stalks. The machine after modification was operated at four cylinder speeds, 4.55, 6.07, 7. 59 and 9.11 m/s (300, 400, 500 and 600 r.p.m.), four feed rates of 2, 4, 6 and 8 kg/min, and three levels of moisture contents of 22.3, 25.5 and 30.3% (wb) for rice straw, respectively. Machine performance, chopping machine capacity (kg/min), cutting length of straw, power consumption (kW), useful power (kW), unit energy (kW.h/Mg) and criterion function cost, were studied in this research. Results of the development machine showed that the percentage of small cutting lengths, were increased by increasing cylinder speed and feed rates and decreased by increasing the moisture contents. The maximum of the percentage of small cutting lengths were (21% > 0.5 cm, 50 % from 0.5 to 1 cm, 12% from 1 to 2 cm and 17% from 2 to 3 cm), at cylinder speed 9.11 m/s (600 r.p.m.) and moisture content of 22.3% in straw and feed rate 8 kg/min. | ||||
| References | ||||
|
Awady, M.N.; M. Shaaban; I. Yehia and M.S. Mira (2001). Review on equipment industry for agricultural-residues management in Egypt. Misr. J. Agric. Eng., 18(4): 96-108.
Awady, M.N., I. Yehia, M.T . Ebaid and E.M.Arif. 2003. Development and theory of cleaner for reduced impurities and Losses. Misr J. Ag., 20(4) : 35 – 68.
El-Berry, A.M.; M.A. Baiomy; H.A. Radwan and E.M. Arif. 2001. Evaluation of (Hematol) machine in rice straw chopping. Misr. J. Agric. Eng., 18(4): 65-76.
El-Haddad, W.Z. 2000. A simplified design and performance study of threshing and winnowing machine suitable for small holdings. M.Sc Thesis, Agric. Mech., Fac. Agric. Kafr El-Sheik, Tanta Univ.
El-Haddad, W. Z. 2004. Manufacture and evaluation chopping, threshing and winnowing machine suitable for the requirements of some crops residues reciculation. Ph. D. Thesis, Agric. Mech. Dept., Fac. of Agric., Kafr El-Sheik University.
El-Zemeity, H.A. 1997. A study to reduce losses of straw during operation of mechanical winnowing and threshing for wheat crop. Misr. J. Agric. Eng., 14(4): 327-341.
Habib, R.A.; B.S. Azzam; G.M. Nassr and A.A. Khattab. 2002. The parameters affecting the cutting process performance of agricultural plants. Misr. J. Agric. Eng., 19(2): 361-372.
Helmy, M.A. 1988. Threshing parameters affecting the performance of local and foreign wheat threshing machines. Misr. J. Agric. Eng., 5(4): 329-343.
Ibrahim, M. K. 1982. Wet milling of wheat grain M.Sc. Thesis, Faculty of Agric., Mansoura Univ., Egypt.
Kepner, R.A.; Roy Bainer and E.L. Barger.1982. Principles of farm machinery. The AV1 publishing Co. Inc. Westport, Connecticut, 392-431 pp.
Mady, M.A. 1999. Developing a manual cutter machine suitable for mechanical cutting of corn stalks. Misr. J. Agric. Eng., 16(3): 449-459.
Suliman, A. EL-R.E; G. EL-D.M.; M.A. Baiomy and A.EL-R.Abdel-Ghany. 2004. Development of cutting knives in crop residues shredder. Misr. J. Agric. Eng., 21(4): 381 -396.
Yumnam,J., and S. Pratap. 1991. Energetic of forage chopping.AMA vol .22 No. 1: 59-63. | ||||
|
Statistics Article View: 167 PDF Download: 383 |
||||
