Vibration Isolation of Asymmetric Rigid Plate Using One and Pair Pre-bent Strut at Each Corner under Static and Dynamic Axial Excitation
Elkafrawy, A., Kandil, A., Helaly, M., Omar, A. (2012). Vibration Isolation of Asymmetric Rigid Plate Using One and Pair Pre-bent Strut at Each Corner under Static and Dynamic Axial Excitation. EKB Journal Management System, 16(2), 13-28. doi: 10.21608/pserj.2012.114379
Ali Elkafrawy; Anwar Kandil; Moustafa Helaly; Abu-Bakr Omar. "Vibration Isolation of Asymmetric Rigid Plate Using One and Pair Pre-bent Strut at Each Corner under Static and Dynamic Axial Excitation". EKB Journal Management System, 16, 2, 2012, 13-28. doi: 10.21608/pserj.2012.114379
Elkafrawy, A., Kandil, A., Helaly, M., Omar, A. (2012). 'Vibration Isolation of Asymmetric Rigid Plate Using One and Pair Pre-bent Strut at Each Corner under Static and Dynamic Axial Excitation', EKB Journal Management System, 16(2), pp. 13-28. doi: 10.21608/pserj.2012.114379
Elkafrawy, A., Kandil, A., Helaly, M., Omar, A. Vibration Isolation of Asymmetric Rigid Plate Using One and Pair Pre-bent Strut at Each Corner under Static and Dynamic Axial Excitation. EKB Journal Management System, 2012; 16(2): 13-28. doi: 10.21608/pserj.2012.114379

Vibration Isolation of Asymmetric Rigid Plate Using One and Pair Pre-bent Strut at Each Corner under Static and Dynamic Axial Excitation

Port-Said Engineering Research Journal
Article 2, Volume 16, Issue 2, September 2012, Page 13-28  XML PDF (850.09 K)
Document Type: Original Article
DOI: 10.21608/pserj.2012.114379
View on SCiNiTO View on SCiNiTO
Authors
Ali Elkafrawy1; Anwar Kandil2; Moustafa Helaly3; Abu-Bakr Omar4
1Port-Said University Department of Production Engineering
2Professor, Production Engineering and Mechanical Design Department, Faculty of Engineering, Port Said University, Port Said, Egypt
3Alexandria University Department of Production Engineering Faculty of Engineering
4Teacher, Mechanical Department, Faculty of Engineering, Suez Canal University, Ismailia, Egypt
Abstract
This paper is concerned with the influence of vibration isolators in the form of post-buckled elastic clamped-clamped one and pair strut to relief the vibrating machines from the harmful effects of vibration. These vibrations are in most cases uncontrollable and lead to sudden failure, therefore, mechanical engineers in preventive maintenance sections have to control, isolate, and minimize the harmful effects of such unwanted vibrations. A mathematical model consists of pre-bent post-buckled one and pair strut acting as vibration isolators supporting an asymmetric rigid plate. The model is subject to axial harmonic excitation at the base, and allowed to displace laterally with respect to axial center line of the isolated plate. The displacement transmissibility is calculated over a wide range of frequencies and plotted in form of design charts. The transmissibility plots are used to recognize the ranges of frequencies, at which isolation can be maintained. The resonance frequencies of the system can be easily depicted from the design graphs. The present study reveals that at resonance frequencies the most effective transmissibility is well below unity. Vibration characteristics are determined under specific frequencies such that the physical behavior of the system can be thoroughly analyzed. All variables used in the analysis are normalized, such that the results aren‟t dependent on any material or geometric property. In this way, the obtained results can be applied over a wide range of elastic materials, regardless of the type of material or section properties. 
Statistics
Article View: 112
PDF Download: 128