Investigating the Effect of Ampere and Cutting Speed on KW of 10 mm Al Using PAM for Optimizing Cutting Quality of Metal Surfaces | ||||
| International Design Journal | ||||
| Article 37, Volume 11, Issue 2 - Serial Number 39, March and April 2021, Page 515-525 PDF (1.2 MB) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/idj.2021.153639 | ||||
 View on SCiNiTO | ||||
| Author | ||||
| Abdulrahman Abu Zeid | ||||
| Assistant Professor, Department of Mineral Products and Ornaments, Faculty of Applied Arts, Helwan University, Egypt | ||||
| Abstract | ||||
| This study aims to investigate the effect of ampere and cutting speed on kerf width (KW) in order to optimize cutting quality of 10 mm Aluminum (Al) surfaces using Plasma Arc Machining (PAM). PAM is an alternative, fast, cheap and technique compared to other techniques like Laser Beam Machining and Abrasive Water Jet Machining. Ampere and cutting speed values are considered to obtain the influence of these parameters on cutting quality. The experimental approach is used to operate 27 specimens through cutting. They are divided into three groups. Different Cutting speeds and 9 different ampere values were used to every group. Cutting path design included straight line, acute angles, square angles, obtuse angles, and curved line. KW measurements were investigated, recorded and evaluated. All specimens results were compared, discussed and represented graphically in order to determine the values of parameters we must use to get the optimum cutting quality. The following are the major results. Some of the recorded values allowed for lower KW using medium amps and cutting speeds and led to higher cutting quality. Also, the use of high cutting speeds at the starting point of cutting KW (key hole) led to minimum cutting width, but the increase in amps had the greatest effect and increased the KW. Also, using fewer amps at the straight line of the cutting path resulted in a lower KW. When increasing the cutting speed, the KW became at the minimal. As for using higher ampere that produce a KW at the maximum sampling level and to obtain appropriate cutting quality, this requires the use of higher cutting speeds with fewer amps to allow a KW at the minimum. This turns out that the relationship is direct between each of the amps and the width of the cut. This means that the more the amps, the more the kerf width; and the less the amps, the kerf width, hence the cut quality. As the KW decreased through using fewer amps at the right angle, the KW increased with the increase in amps at the same cutting speeds used for the right angle and in the middle of the curve along the cutting path. In addition, the KW quality at the obtuse and the right angles was significantly lower than the KW quality in the case of the acute angle and the angle that corresponds to the diagonal line with the curve. But, when reducing the ampere, the KW decreased and the cutting quality increased. On the other hand, the cutting was bad at the acute angle and at the angle that corresponds to the diagonal line with the curve, so it should be avoided when designing the cutting path with a plasma arc. Also, using high cutting speeds at acute angle with fewer amps produced lower KW and higher quality. Even all the cutting speeds and amps used at the acute angle produced a KW at the maximum, contrary to the cut at the right angle where the cut width was lower and at the minimum. In addition, the use of a lower speed and a lower ampere allowed a lower cut width at the end of the curve of the cutting path. It turned out that the relationship is inversely between the cutting speed and the KW. The higher the speed, the lower the KW and the higher the cutting quality, the lower the cutting speed, the greater the cutting width and the lower the cutting quality. Also, the thickness of 10 mm Al prevented melting of the cutting edges during operating and the higher thickness helped to keep the Heat Input to work, differently from thin thicknesses. The difficulty of controlling the cutting of thin thicknesses of Al was also shown because the surface retains the heat generated from operating and melting. The lowest reading was 2,217 mm at the right angle as a result of using the 190 ampere values with the cutting speed of 1100 mm /min, arc voltage 130 volt and gass pressure 4.2 bar. This is the optimum value to obtain the minimum KW and higher cutting quality. | ||||
| Keywords | ||||
| Plasma Arc Machining; Cutting Current Amperee; Cutting Speed،; Kerf Width،; Cutting Quality | ||||
| References | ||||
|
Abouzaid, A., Newishy, M., & AlQotari, I. (2018). The effect of machining parameters on 0.8 mm thickness brass thin sheets using plasma arc technique for optimizing cutting quality of metal products. The 5th international conference of Applied Arts [CD ROM]: International Design Journal. Received for peer reviewing on March 18 2018, accepted for publication 23 April 2018, and should be appear on line on 15th May 2018. 2. Ananthakumar, K., Rajamani, D., Balasubramanian, E. and Davim, J.P., 2019. Measurement and optimization of multi-response characteristics in plasma arc cutting of Monel 400™ using RSM and TOPSIS. Measurement, 135, pp.725-737, Received on 14 May 2018, Revised 30 October 2018, Accepted 1 December 2018. From ScienceDirect database. https://doi.org/10.1016/j.measurement.2018.12.010 3. Bhowmick, S., Basu, J., Majumdar, G. and Bandyopadhyay, A., 2018. Experimental study of plasma arc cutting of AISI 304 stainless steel. 7th International Conference of Materials Processing and Characterization. Materials Today: Proceedings, 5(2), pp.4541-4550, from ScienceDirect database.https://doi.org/10.1016/j.matpr.2017.12.024. 4. Blanks, C. F. S. (1986). Selected Abstracts of Materials Literature. 5. Bini, R., Colosimo, B.M., Kutlu, A.E. and Monno, M., 2008. Experimental study of the features of the kerf generated by a 200 A high tolerance plasma arc cutting system. Journal of materials processing technology, 196(1-3), pp.345-355. Received 10 May 2006, received in revised form 1 February 2007, accepted 29 May 2007. From ScienceDirect database. https://doi.org/10.1016/j.jmatprotec.2007.05.061 6. BOC. (2011). Facts about plasma technology and plasma cutting. Plasma working group at Linde AG, Linde Gas Department, and specialists from the company Kjellberg Finsterwalde Elektroden und Maschinen GmbH. Auckland: NewZealand. 7. Dong, Y., Zheng, K., Fernandez, J., Li, X., Dong, H. and Lin, J., 2017. Experimental investigations on hot forming of AA6082 using advanced plasma nitrocarburised and CAPVD WC: C coated tools. Journal of Materials Processing Technology, 240, pp.190-199. Received 26 April 2016, received in revised form20 September 2016, accepted 24 September 2016, available online 28 September. From ScienceDirect database. https://doi.org/10.1016/j.jmatprotec.2016.09.023 8. Gangil, M., Pradhan, M. K., & Purohit, R. (2017). Review on modelling and optimization of electrical discharge machining process using modern Techniques. Conference Committee Members of 5th International Conference of Materials Processing and Characterization. Mater. Today Proc., 4(2), 2048-2057, from ScienceDirect database. https://doi-org.sdl.idm.oclc.org/10.1016/j.matpr.2017.02.050 9. Kandpal, B. C., & Singh, H. (2015). Machining of aluminium metal matrix composites with electrical discharge machining-a review. 4th International Conference on Materials Processing and Characterization. Materials Today: Proceedings, 2(4-5), 1665-1671, from ScienceDirect database. https://doi.org/10.1016/j.matpr.2015.07.094 10. Klimpel, A., Cholewa, W., Bannister, A., Luksa, K., Przystałka, P., Rogala, T., Skupnik, D., Cicero, S. and Martín-Meizoso, A., 2017. Experimental investigations of the influence of laser beam and plasma arc cutting parameters on edge quality of high-strength low-alloy (HSLA) strips and plates. The International Journal of Advanced Manufacturing Technology, 92(1-4), pp.699-713, 23 May 2016 / Accepted: 1 February 2017 / Published online: 3 March 2017. From SprinkerLink database. https://doi.org/10.1007/s00170-017-0119-2 11. Kudrna, L. and Merta, M., 2017. The technology of plasma cutting on a CNC machine. International Multidisciplinary Scientific GeoConference: SGEM: Surveying Geology & mining Ecology Management, 17(1.3), pp.949-956, from ProQuest database. doi:10.5593/sgem2017/13 12. Shakhashiri, B. Z. (2012). Chemical of the week: aluminum. University of Wisconsin: SciFun. org. 13. Salonitis, K., & Vatousianos, S. (2012). Experimental investigation of the plasma arc cutting process. Procedia cirp, 3, 287-292, from ScienceDirect database. https://doi.org/10.1016/j.procir.2012.07.050 14. https://ar.wikipedia.org/wiki/%D8%A3%D9%84%D9%88%D9%85%D9%86%D9%8A%D9%88%D9%85#cite_note-28. 15. https://www.hypertherm.com/hypertherm/hyperformance/hyperformance-hpr130xd | ||||
|
Statistics Article View: 213 PDF Download: 278 |
||||
