Automation of Design Tool for an Axial Flow Gas Turbine Stage Used in Small Gas Turbine Engine
Elqussas, N., Elzahaby, A., Khalil, M., Elshabka, A. (2017). Automation of Design Tool for an Axial Flow Gas Turbine Stage Used in Small Gas Turbine Engine. EKB Journal Management System, 17(AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 17 – April 11 - 13, 2017), 1-14. doi: 10.21608/asat.2017.22792
Nader Elqussas; Aly M. Elzahaby; Mohamed K. Khalil; A. M. Elshabka. "Automation of Design Tool for an Axial Flow Gas Turbine Stage Used in Small Gas Turbine Engine". EKB Journal Management System, 17, AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 17 – April 11 - 13, 2017, 2017, 1-14. doi: 10.21608/asat.2017.22792
Elqussas, N., Elzahaby, A., Khalil, M., Elshabka, A. (2017). 'Automation of Design Tool for an Axial Flow Gas Turbine Stage Used in Small Gas Turbine Engine', EKB Journal Management System, 17(AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 17 – April 11 - 13, 2017), pp. 1-14. doi: 10.21608/asat.2017.22792
Elqussas, N., Elzahaby, A., Khalil, M., Elshabka, A. Automation of Design Tool for an Axial Flow Gas Turbine Stage Used in Small Gas Turbine Engine. EKB Journal Management System, 2017; 17(AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 17 – April 11 - 13, 2017): 1-14. doi: 10.21608/asat.2017.22792

Automation of Design Tool for an Axial Flow Gas Turbine Stage Used in Small Gas Turbine Engine

International Conference on Aerospace Sciences and Aviation Technology
Article 85, Volume 17, AEROSPACE SCIENCES & AVIATION TECHNOLOGY, ASAT - 17 – April 11 - 13, 2017, April 2017, Page 1-14  XML PDF (745.94 K)
Document Type: Original Article
DOI: 10.21608/asat.2017.22792
View on SCiNiTO View on SCiNiTO
Authors
Nader Elqussas1; Aly M. Elzahaby2; Mohamed K. Khalil1; A. M. Elshabka1
1Egyptian Armed Forces, Egypt.
2Prof, Tanta University, Egypt.
Abstract
Abstract: This paper describes the automation of 3D design and aerothermodynamic analysis of a high pressure, single-stage axial flow turbine driving the compressor of the small gas turbine engine Jet Cat p200 using an analytical method. The specifications of design are based on the reverse engineering of the small gas turbine. Baseline design parameters such as flow coefficient, stage loading coefficient are close to 0.5 and 1.16 respectively with maximum flow expansion in the NGV rows. In the thermal cycle and 1D analysis calculations, the total conditions of all engine stations and all design controlling parameters are determined. In 2D design analysis, the mean line approach is used to generate the turbine flow path and 2D airfoil design, and by using the free vortex law of blading, five blade sections are generated. These sections are at hub, mean and tip and two intermediate sections between hub-mean and mean-tip using an approximate method to the Ainley, Mathieson, Dunham and Came loss model to meet the design constraints. An average exit swirl angle of less than 5 degrees is achieved leading to minimum losses in the stage. Also, NGV and rotor blade numbers are chosen based on the original turbine object. Blade profile is redesigned using the results from blade-to-blade analysis and through-flow analysis using special analytical method, [1]. Aerothermodynamic parameters like pressure ratios, aerothermodynamic power, and efficiencies are computed analytically. The results are compared with the published data in the engine manual.
Statistics
Article View: 168
PDF Download: 1,417