Influence of Counterface Materials on the Tribological Behavior of Dental Polymethyl Methacrylate Reinforced by Single-Walled Carbon Nanotubes (SWCNT)
A. K., A., M. O., M., W. Y., A., A. M., S., A. H., E. (2022). Influence of Counterface Materials on the Tribological Behavior of Dental Polymethyl Methacrylate Reinforced by Single-Walled Carbon Nanotubes (SWCNT). EKB Journal Management System, 3(2), 68-79. doi: 10.21608/svusrc.2022.147497.1056
Ameer A. K.; Mousa M. O.; Ali W. Y.; Samy A. M.; El-Abd A. H.. "Influence of Counterface Materials on the Tribological Behavior of Dental Polymethyl Methacrylate Reinforced by Single-Walled Carbon Nanotubes (SWCNT)". EKB Journal Management System, 3, 2, 2022, 68-79. doi: 10.21608/svusrc.2022.147497.1056
A. K., A., M. O., M., W. Y., A., A. M., S., A. H., E. (2022). 'Influence of Counterface Materials on the Tribological Behavior of Dental Polymethyl Methacrylate Reinforced by Single-Walled Carbon Nanotubes (SWCNT)', EKB Journal Management System, 3(2), pp. 68-79. doi: 10.21608/svusrc.2022.147497.1056
A. K., A., M. O., M., W. Y., A., A. M., S., A. H., E. Influence of Counterface Materials on the Tribological Behavior of Dental Polymethyl Methacrylate Reinforced by Single-Walled Carbon Nanotubes (SWCNT). EKB Journal Management System, 2022; 3(2): 68-79. doi: 10.21608/svusrc.2022.147497.1056

Influence of Counterface Materials on the Tribological Behavior of Dental Polymethyl Methacrylate Reinforced by Single-Walled Carbon Nanotubes (SWCNT)

SVU-International Journal of Engineering Sciences and Applications
Article 7, Volume 3, Issue 2, December 2022, Page 68-79  XML PDF (786.67 K)
Document Type: Original research articles
DOI: 10.21608/svusrc.2022.147497.1056
View on SCiNiTO View on SCiNiTO
Authors
Ameer A. K.1; Mousa M. O.1; Ali W. Y.1; Samy A. M.1; El-Abd A. H.2
1Dept. of Production Engineering & Mechanical Design, Faculty of Engineering, Mini University, Egypt
2Dept. of Mechanical Power Engineering, El-Arish High Institute of Engineering and Technology, Ministry of Higher Education, Egypt.
Abstract
The counterface materials that used in the study were polymethyl methacrylate (PMMA), stainless steel, porcelain, amalgam and buffalo teeth. Friction coefficient and wear are measured by testing the specimens on a reciprocating device at room temperature. It can be noticed that the counterface materials had a distinct effect on the coefficient of friction, wear and \ surface roughness of the PMMA composites. According to the results, it was found that the buffalo tooth and porcelain counterface lead to higher wear resistance, while the amalgam material showed minimal wear resistance under dry and wet conditions. The amalgam material had the highest coefficient of friction value in the dry and wet test, the PMMA material showed the highest value of the coefficient of friction. The surface roughness of stainless steel showed the highest value while the other counter-face materials can have the same value in the dry state while in the wet state the surface roughness of the buffalo teeth showed the minimum value, while other counterface materials may have the same value.
Keywords
Polymethyl methacrylate (PMMA); Single-walled carbon nanotubes (SWCNT); wear; friction coefficient; Counterface material
Statistics
Article View: 181
PDF Download: 140