WEAR BEHAVIOR OF HYBRID COMPOSITE REINFORCED WITH TITANIUM DIOXIDE NANOPARTICLES | ||||
| Journal of Advanced Engineering Trends | ||||
| Article 8, Volume 39, Issue 1, January 2020, Page 89-101 PDF (920.67 K) | ||||
| DOI: 10.21608/jaet.2020.75738 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| A. Meshref A.* ; Mazen A. A.; El-Giushi M. A.; Ali W. Y. | ||||
| Department of Production Engineering & Design, Faculty of Engineering, Minia University, EGYPT. | ||||
| Abstract | ||||
| The aim of the present study is to investigate the influence of polymerization times, normal loads and titanium dioxide nanoparticles content on the wear of hybrid composite resin reinforced with titanium dioxide (TiO2) nanoparticle. The materials used are hybrid composite resin and titanium dioxide nanoparticles (TiO2nanoparticles). Four groups of composite resin samples are prepared; one as received and three groups reinforced with TiO2nanoparticles in contents of 0.1, 0.2 and 0.3 wt. %. Hybrid composites resin is manually mixed with TiO2 nanoparticles. The resulting blend is packed into plastic cylindrical bars. The samples are then cured from both sides for 10, 20, 40, 60 and 80 seconds using a visible light curing unit. To determine the wear, all samples are tested with two-body abrasion, reciprocating sliding apparatus at room temperature. The test conditions are; sliding velocity= 60 strokes/min, load= 6, 8, 10, 12 and 14 N, time= 60 seconds. Results show that the wear decreases with the increase of polymerization time at all normal loads. Results showed also that wear depends on the normal load. The wear initially decreased and reached a minimum at a concentration of 0.1 wt. % TiO2 nanoparticles, above 0.1 wt. % TiO2 nanoparticles, the aggregation of TiO2 nanoparticles led to increase of the wear. The present study suggests that in order to minimize wear, it is important to use relatively higher polymerization time, lower TiO2content and lower force of chewing. | ||||
| Keywords | ||||
| Polymerization time; dental nanocomposite; Wear; Titanium dioxide; Nanoparticles; hybrid composite resin; normal load | ||||
| References | ||||
|
1. Powers J. M., Douglas W. H. and Craig R. G., “Wear of Dimethacrylate Resins Used in Dental Composites”, Wear, Vol.54 ,pp. 79 – 86, (1979).
2. Liqun C., Xinyi Z., Xu G., Shouliang Z., “An in Vitro Investigation of Wear Resistance and Hardness of Composite Resins, Int J Clin Exp Med,Vol. 6, No. (6), pp. 423-430,( 2013).
3. Witold B. , Vera K. , Domagoj V.and Jenna W., “Tribology of Polymers and Polymer-Based Composites”, Journal of Materials Education, Vol.32, No. (5-6), pp. 273 – 290,(2010).
4. Yanni T., Yong L., Liam M. Grover, Baiyun H., “Wear Behavior of Light Cured Dental Composites Filled with Porous Glass–Ceramic Particles”, Journal of the mechanical behavior of biomedical materials, Vol. 3,pp. 77 – 84, (2 0 1 0).
5. Ibrahim M. Hamouda, HagagAbd Elkader, “Evaluation the Mechanical Properties of Nanofilled Composite Resin Restorative Material, Journal of Biomaterials and Nanobiotechnology, Vol. 3, pp. 238-242, (2012).
6. Ayman A. Aly, El-Shafei B. Zeidan, AbdAllah A. Alshennawy, Aly A. El-Masry, Wahid A. Wasel, “Friction and Wear of Polymer Composites Filled by Nano-Particles”, World Journal of Nano Science and Engineering, Vol. 2, pp. 32-39,(2012).
7. Rymuza Z., “Tribology of Polymers”, Archives of Civil and Mechanical Engineering, Vol. VII, No. (4), pp. 177- 184,(2007).
8. ASM International, ASM Handbook Volume 18, “Friction, Lubrication, and Wear Technology”, American Society for Metals, Metals Park, Ohio, pp. 341-347, (1992).
9. Nuruzzaman, D.M., Chowdhury, M.A., and Rahaman, M.L. “Effect of Duration of
Rubbing and Normal Load on Friction Coefficient for Polymer and Composite Materials”, Industrial Lubrication and Tribology, Vol. 63, pp. 320 – 326,( 2011).
10. Ramadan M. A., Abu Elainin H. M., Mazen A. A., Ali W. Y., "Abrasive Wear of Teeth", Journal of the Egyptian Society of Tribology Vol. 8, No. 2, April 2011, pp. 56 – 66, (2011). 11. Ramadan M. A., Ali W. Y. and Mazen A., "The Mechanical Wear of Teeth, Dental Wear", Lab Lambert Academic Publishing, ISBN: 978-3-659-00089-8, US, (2012). 12. Lu H., Lee Y., OguriM, Powers J., “Properties of a Dental Resin Composite with a Spherical Inorganic Filler”, Operative Dentistry, Vol.31, No. 6, pp.734-740, (2006).
13. Aljosa I., Tijana L., Larisa B., Marko V., Influence of Light-Curing Mode on the Mechanical Properties of Dental Resin Nanocomposites, Procedia Engineering, Vol. 69, pp. 921 – 930, (2014).
14. Manhart J., KunzelmannK.H., Chen H.Y., HickelR., “Mechanical Properties and Wear Behavior of Light Cured Packable Composite Resins, Dental Materials, Vol. 16, pp. 33–40, (2000).
15. Agarwal G., Patnaik A., Sharma R. K.,”Parametric Optimization and Three-Body Abrasive Wear Behavior of Sic Filled Chopped Glass Fiber Reinforced Epoxy Composites”, International Journal of Composite Materials, Vol. 3, No. (2), pp. 32-38, (2013).
16. Ramadan M. A., Abu Elainin H. M., Mazen A. A. and Ali W. Y., "Influence of Brushing Force on Abrasive Wear of Teeth", Journal of the Egyptian Society of Tribology Vol. 8, No. 4, October 2011, pp. 47 – 59, (2011). 17. Chang L., Zhang Z., Breidt C. and Friedrich K., “TribologicalProperties of Epoxy
Nanocomposites: I. Enhancement of the Wear Resistance by Nano-TiO2 Particles,” Wear, Vol. 258, No. 1-4, pp. 141-148, (2004).
18. Meshref A. A., Mazen A. A., El-Giushi M. A. and Ali W. Y., “Effect of Curing Process of Dental Nanocomposite Resin on Shore Hardness , EGTRIB Journal,Vol. 13, NO. 2, pp. 25 – 37,(2016).
19. Hegde M. N., Hegde P., Bhandary S. , Deepika K., “An evaluation of compressive strength of newer nanocomposites: An in vitro study,” Journal of Conservative Dentistry, Vol. 14, pp. 36-39, (2011).
20. Cai LiS., Na Li Y., “Journal of Applied Polymer Science”, Vol. 116,pp. 2965 -2969, (2010). | ||||
|
Statistics Article View: 251 PDF Download: 297 |
||||
