PERFORMANCE OF LOCAL MAIZE CHOPPING MACHINE ATTACHED WITH FEEDING BELT | ||||
| Misr Journal of Agricultural Engineering | ||||
| Article 4, Volume 32, Issue 1, January 2015, Page 67-86 PDF (665.01 K) | ||||
| Document Type: Original Article | ||||
| DOI: 10.21608/mjae.2015.98678 | ||||
 View on SCiNiTO | ||||
| Authors | ||||
| M. A. Aboamera1; M. A. Mohamed2; G. R. Gamea2; E. M. Gomaa3 | ||||
| 1Professor of Agric. Eng. Dept. Menofia University, Egypt | ||||
| 2Professor of Agric. Eng. Dept. Menofia University, Egypt. | ||||
| 3Demonstrator of Agric. Eng. Dept. Menofia University, Egypt. | ||||
| Abstract | ||||
| A transported belt was attached to a traditional chopping machine to improve its performance during the chopping process of maize. Evaluation the chopping performance focused upon changing machine rotational speed, moisture content of corn and feeding quantity. The highest actual chopping time was 14.16 sec occurred at 1.56 kg of feeding quantity and 54.11% of corn moisture content at rate of 9.07 sec/kg. The highest rate of fuel consumption was 3.65 lit/h. kg. was observed at 73.45% of corn moisture content with 1.56 kg of feeding quantity. Maximum cutting efficiency (96.96%) was occurred at 54.11% of corn moisture content at 0.67 kg of feeding quantity. The highest machine productivity (2.55 ton/h) was observed at 2000 rpm of machine rotational speed with 1.56 kg of feeding quantity. | ||||
| Keywords | ||||
| modified chopping machine; mechanical chopping process of maize; actual time; maize chopping productivity; moisture content of maize during chopping process | ||||
| References | ||||
|
Adgidiz, (2007) "Development and performance evaluation of a forage chopper". Journal of Agricultural Engineering and Technology (LAET). Federal University of Technology, Minna, Niger state, Nigeria. volume 15, 2007. P .P. 12-24.
AOAC (1990) "Association official Analytical chemists". 15th edn. Washington Dc, U.S.A
El-Ashry. A. S.; E. H. Musa; and I. S. Yousef(2004) Development of a combination unit for cutting and chopping corn stalks during harvesting. Misr J. Ag. Eng., 21 (3): 685-696.
El-Sisi, S. F. B (2012). Some engineering factors affecting handling of residuals and its relation to environment. M. Sc. thesis, Menofia Univ., Agric. Eng. Department. June 2012. P.P. 1-129.
Embaby, A. T. (1985) "A comparison of the different mechanization systems for cereal crop production". M.Sc thesis, Faculty of Agriculture., Cairo University.
Extension dairy team (2012). Making quality corn silage. Iowa State University, Iowa Beef Center. P.P, 1:3.
Ibrahim, A. A. (2006) Study of some engineering factors affecting the performance of a machine for cutting field residues. M. Sc. thesis, Menofia Univ. Agric. Eng. Department. 2006. P.P. 1-142.
Lotfy, A. (2003) "Development and performance evaluation a machine for cut and throw agricultural residues". Misr, J.AG. Eng., 20(3): 724-736.
Mohamed, H. I. A (2007). Effect of mechanical chopping and adding different farm residues on soil physical properties and wheat yield. M. Sc. thesis, Zagazig Univ., Agric. Eng. Department. P.P. 1-85.
Mohamed, M.A. ; G.H, El-Sayed ; and K.E.S.Hegazy (1999). Some factors affecting power and energy requirements for forage harvesster. Msr. J. Ag. Eng., 16(4), October, 1999.
Morad, M. M. ; M. A. Arnaout ; O. A. Omar ; and H. I. Ahmed (2007) "Effect of mechanical chopping and adding different farm residues on soil physical properties and wheat yield"Zagazig J. Agric. Res., Vol. 34 No. (4) pp. 781-804.
Umunna, N. N. and Agishi, E. C.( 1988 ) "Nutritive value of savanna grasses and harvest residues for use in dry season animal feeding". Invited paper at the scrub savannah studies symposium.
Bauchi, Nigeria. February, 7 – 8, 1988.
Younis, S. M.; M. I. Ghonimy.; M. A. Baiomy.; and T. H. Mohamed (2002) "Techno-economic evaluation of a developed field crop residues chopper". Misr, J.AG.Eng, 19(4): 63-80. | ||||
|
Statistics Article View: 118 PDF Download: 176 |
||||
